The range thermostat is also commonly known as a stove, oven, cooktop, or range thermal fuse. This thermostat protects your oven from excessive heating, and will shut the oven heat off if excessive heating is detected. This is a genuine part sourced directly from the original manufacturer. You may need to replace this part if your applian...Read morece will not heat properly. It is made of metal and is approximately 1 inch in diameter. This part is sold individually. It is recommended to order a spare, especially if you commonly use the self-cleaning function in your oven.
This temperature sensor, also known as a thermistor, is compatible with various makes and types of appliances. This thermistor uses electrical currents to detect the interior temperature of the appliance it is in and by working with the control board, the board adjusts the level of cooling or heating through its heating or cooling element...Read more, depending on what is needed. If your appliance is being improperly heated or cooled, the temperature sensor may be to blame, and can be tested with a multimeter to check for continuity to see whether it is defective. Check your user manual for exact placement of this thermistor and any diagnostic information.
The fuse-time delay may also be known as a line fuse or a microwave fuse, and it is a piece for your microwave. The function of this part is to shut off the microwave if there is a power surge, in order to protect your microwave from damage. You should consider having a service technician install this part as the high-voltage capacitors i...Read moren a microwave can contain a very harmful electrical charge, even when the microwave is unplugged and has been inactive for some time. The tools that would be needed to complete this installation include a Phillips screwdriver, an insulated screwdriver, and a pair of pliers.
This is a genuine OEM leveling leg for various models of LG ranges. This leg is used to stabilize and support the range, and if damaged, broken, or missing, will cause your range to rock back and forth. Installing this leg simply requires you to lift on the corner you are installing it under, and then screw it in place until your range is...Read more stable. This approximately 2-inch leveling leg is sold individually, so if your range has multiple legs that are broken or missing, consider how many legs you need to order.
Upgrade your oven with this durable gliding shelf rack, designed to provide a stable surface for baking, roasting, and broiling. Its smooth sliding design makes it easy to insert and remove dishes, offering convenience and efficiency during cooking. Built to support heavy cookware, this rack measures approximately 24 3/8" x 16 1/2" and fe...Read moreatures a sturdy construction for long-lasting performance. Cleanup is simple thanks to its smooth finish, making it a practical and reliable addition to your kitchen. Installation is quick—just slide the rack into the designated oven supports for immediate use.
A dual radiant heater supplies heat to a cooking area beneath a glass cooktop. Replacement may be needed when one zone does not warm, only the inner or outer section works, or the element has a visible break. Normal radiant burners cycle on and off, so cycling alone does not prove a failure. Check the control switch and connections first,...Read more then match the replacement by full model number, location, size, mounting points, and electrical rating. Disconnect the range at the breaker and confirm the circuit is dead before service. Handle sharp metal edges and the glass top carefully, and return every bracket, shield, and wire to its original position.
This transparent inner door glass is designed for LG range ovens and serves as a key component in maintaining heat insulation while allowing visibility into the oven during cooking. Made from heat-resistant material, it helps retain internal temperatures for consistent baking and roasting performance. Replacing a damaged or cracked inner ...Read moreglass restores the oven’s energy efficiency and ensures safe operation. This OEM replacement part is manufactured to fit specific LG models and is intended for use when the original glass is chipped, broken, or compromised. Installation typically involves removing the oven door, disassembling the inner panel, and securely fitting the new glass in place. Always confirm your oven model before installation to ensure compatibility.
The sub PCB assembly (also referred to as a relay board), is a part for your range. If your oven is overheating, this might indicate that your sub PCB assembly needs to be replaced. You will need a Phillips screwdriver to remove the screws securing the upper rear access panel brackets. Also, remove the screws securing the panel and detach...Read more. Take note of how the wires are currently connected to the board. This board is held in place by screws and can be removed. You will then need to release the retaining clips to release the entire board. The new sub PCB assembly should snap into place.
This radiant heater may also be known as a radiant surface element and is a part for your range. The function of this heater is to supply heat to the cooking area that is on the top of the range. This piece is roughly 9 inches long, and 7 inches wide. The most common symptom for needing to replace your radiant heater is if your burner is ...Read morenot heating. Before replacing this part, it is always a good idea to test it for continuity. To make this installation you will need a Phillips screwdriver, and a 14-inch nut driver.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Hammer 1, Glass range top and heating element 0
22 of 52 peoplefound this instruction helpful.
Richard from CHESAPEAKE, VA
Easy
30 - 60 mins
Screw drivers
Dropped a hammer on the range while removing a ceiling light. Viewed a How-To video on Google. Ordered the needed parts. Followed the steps from the How-To video. Reinstall was a bit tricky by myself - could have used an extra set of hands. I have a few words of caution: 1) Put something between the range top and range - like a
... Read moresheet or drop cloth - to prevent a dropped screw from falling into a crevice in the stove. I dropped a screw and was unable to retrieve it, even with a magnet. 2) Makes sure you remove all bumpers, screws, clips, etc. from the item being replaced and put them on the new item if the new item does not come with replacement bumpers, screws, etc.
Read less
Was this helpful?
Thank you for voting!
Oven would initially start to heat up but would not hold its temp
6 of 8 peoplefound this instruction helpful.
Leonard from Plano, TX
Really Easy
15 - 30 mins
Pliers, Screw drivers
I searched online and found someone that seemed to have the exact problem. That person had replaced the lower burner and the same PCB board I replaced. I was able to test the lower burner without removing it and it tested OK. The PCB board in the article I had checked was burned and obviously bad but mine was not. I took a chance and
... Read moreordered just the PCB board. I replaced this board and the oven now works perfectly. I seems this board was not turning on the bottom burner but the system thought it was working fine.
Read less
Was this helpful?
Thank you for voting!
wouldn't turn on
2 of 3 peoplefound this instruction helpful.
Michael from MILWAUKEE, WI
Easy
30 - 60 mins
Screw drivers
simply take picture b4 you start then replace same way.
WARNING!!! MAKE SURE YOU HAVE RIGHT PART!! They are very slow to return any type of credit