LNC8435A80 Norge Dryer Parts & Repair Help | PartSelect
Models > LNC8435A80

LNC8435A80 Norge Dryer - Overview

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
(321)
PartSelect #:PS346995
Manufacturer #:341241
This dryer drum belt (Whirlpool Dryer Belt, Drive Belt) has four ridges, three grooves and is 1/4" wide, and 92 1/4 inches in length. It comes in black and is made of rubber. The b...
$16.60
In Stock
(119)
PartSelect #:PS334310
Manufacturer #:279834
When the igniter reaches a high enough temperature, these coils (Coil Valve, Dryer Gas Valve Coil Kit, Dryer Valve Coil Kit, Gas Valve Solenoid) work together to open the gas valve...
$28.24
In Stock
(44)
PartSelect #:PS2162282
Manufacturer #:LA-1053
The high limit kit comes with three separate thermal fuses for dryers. One electric thermal fuse with a limit of 258, one gas high limit at 240, and one gas and electric high limit...
$31.10
In Stock
(12)
PartSelect #:PS11741429
Manufacturer #:WP338906
If your gas dryer is not heating up or igniting, then replacing the flame sensor, located in the burner assembly, could solve it. This part senses heat from the igniter to monitor ...
$42.69
In Stock
(19)
PartSelect #:PS2162263
Manufacturer #:LA-1003
This door catch kit is designed for use in dryers. This is an authentic OEM replacement part. This catch assembly ensures the door of your appliance will close, and remain closed. ...
$25.34
In Stock
(4)
PartSelect #:PS11740719
Manufacturer #:WP31001529
If this part appears to be too wide for your particular appliance, per the manufacturer, all you have to do is pull it apart.
$51.54
In Stock
(2)
PartSelect #:PS11742801
Manufacturer #:WP53-0106
This is a beige blower wheel that is made of plastic. Manufactured to fit a 1/'2 inch motor shaft, this blower wheel is 3-1/8 inches deep, and the diameter of the wheel is 7-1/8 in...
$50.27
On Order
(2)
PartSelect #:PS11740735
Manufacturer #:WP31001747
The drum felt seal, used in dryers, allows the drum to smoothly glide with minimal friction. If any of the following symptoms occur with your dryer, replacing the felt seal can be ...
$24.62
In Stock
(2)
PartSelect #:PS2003584
Manufacturer #:12002126
This kit includes 2 glides (left and right), 2 pads with adhesive backing and 1 support brace.
$60.13
On Order
(1)
PartSelect #:PS2162266
Manufacturer #:LA-1006
Pad has adhesive backing.
$20.48
In Stock
Questions and Answers for LNC8435A80
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer ran but would not heat

  • Customer: Gary from Haverhill, NH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 355 of 395 people found this instruction helpful
PartSelect showed seven different possibilities why the dryer wouldn't heat. I removed the two screws to remove the bottom panel and turned the dryer on and noticed that the heating element that ignites the gas was working fine. This meant that it was not getting gas so it could be the gas valve or one of the two gas valve coils which are located on top of t... read more

Electric dryer would not heat - Thermal fuses - $25 fix - I love DIY

High Limit Kit – Part Number: LA-1053
  • Customer: Ronald from Fredericksburg, VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 207 of 226 people found this instruction helpful
1. Unplug dryer from power outlet
2. Lift dryer top from front (hinged in rear). Just friction holding top down. Use flat scewdriver wrapped in cloth to help lift.
3. Locate heating element - rear top behind drum
4. Unplug red wires to the high limit thermal fuse
5. Unplug red wires to the heating element
6. Unlug white wires to the ... read more

Dryer flame goes out after about 8-minutes from start and won’t work again until a 15-minute rest.

  • Customer: andy from Bethesda, MD
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 170 of 91 people found this instruction helpful
There was no problem with lint build-up within the dryer & the exhaust vent. I removed the gas cycling thermostat & thermal fuse from system & dryer still was not operating correctly. The radiant sensor & hi-limit thermostat both seemed to be operating correctly. That left either of the two coils as the culprits. I replaced both coils & the problem was co... read more