Restore visibility in the microwave cavity or over the cooktop with this replacement incandescent lamp. The 30 watt bulb uses a screw base to connect to the light socket and provides illumination when the appliance lighting is activated. A burned out filament may leave the area dark while the microwave continues operating normally. Replac...Read moreing a failed bulb restores light for checking food or viewing the cooking surface below. Disconnect power, allow the lamp to cool, and follow the appliance instructions for access to the bulb. This is an OEM part sourced directly from the manufacturer.
This micro-switch is designed for use in your microwave. The function of this part is to monitor the door latch position and communicate to the electronic control board whether the latch is open or closed. If your microwave does not provide heat, or will not start properly, you may need to replace the micro-switch. This part is approximat...Read moreely 1 inch in length and 3/4-inch in width. It is made of black plastic with two metal prongs. This is an OEM part sourced directly from the manufacturer. This part is sold individually. Be sure to disconnect the microwave from the power source before you begin this repair.
This microwave door interlock switch responds to the door latch, helping prevent cooking operation while the door is open. Its small actuator changes the electrical contact when the door opens or closes. A worn or damaged switch may prevent the microwave from starting even when the door is fully shut. Replacing a faulty switch helps resto...Read morere proper door detection within the safety interlock system. Internal microwave components can retain a dangerous electrical charge after unplugging, so disconnecting power alone does not make them safe to handle. This is an OEM part sourced directly from the manufacturer.
This bracket holds the metal or plastic flapper that closes off the exhaust duct when the fan is not running and opens when the fan turns on. If the exhaust fan on your microwave does not appear to be working, the problem may be with the damper assembly. If the damper does not open and close easily, check for any damage to the bracket, an...Read mored replace if it is damaged or faulty. This genuine OEM exhaust damper measures approximately 12 inches long by 5 inches wide.
This charcoal filter in manufactured to fit a microwave. It removes food odors from the air circulating through your appliance vent. Youi may need to replace this part if you notice odor when cooking your food or if your filter is clogged. It measures approximately 9.5 inches wide and 3 inches tall, and is black in color.
Exhaust air passes through this microwave vent damper when the ventilation fan runs. The metal flap opens with outgoing airflow to let steam and cooking odours enter the exhaust duct, then closes when airflow stops to help limit outside drafts. A bent, warped, or stuck flap may restrict ventilation or allow air to flow back into the kitch...Read moreen. Replacing a damaged damper helps restore free flap movement and proper exhaust operation, providing a movable barrier at the duct opening between fan uses. This is an OEM part sourced directly from the manufacturer.
Electrical overload protection comes from this microwave time delay fuse, rated at 20 amps and 250 volts. It tolerates brief startup current while opening the circuit during a sustained overload or short circuit. A blown main fuse may leave the microwave without power or prevent it from starting. The fuse cannot be reset and requires repl...Read moreacement once it opens. Internal microwave components can retain a dangerous electrical charge after unplugging, so disconnecting the power cord alone does not make internal handling safe. This is an OEM part sourced directly from the manufacturer.
Secure door closure relies on this black plastic microwave door latch hook. Installed inside the door assembly, it engages the latch openings and operates the safety interlock switches when the door closes. A cracked hook or damaged latch may prevent the door from staying shut or keep the microwave from starting. Replacing a damaged latch...Read more helps restore proper mechanical engagement and door operation. The hook moves with the door release mechanism, allowing the door to open when released and latch again when closed. This is an OEM part sourced directly from the manufacturer.
The turntable motor coupler connects the turntable motor to the tray. If the turntable on your microwave will not rotate, you may have a faulty motor coupler. The coupler commonly has a D shaped opening that fits tightly onto the motor shaft. If it is cracked, or worn it will need to be replaced. This is a genuine OEM replacement part sourced directly from the manufacturer.
This genuine OEM light socket provides power to the light bulb in your microwave while holding it in place. This light socket is two pronged and the bulb should screw easily into it. If your light bulb will not light, check the bulb itself and light socket’s connection. If the socket is broken, or faulty it should be replaced immediately....Read more Make sure to remove the high-voltage capacitor from your microwave before beginning this repair.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Bob - For model number LMV1813ST
July 29, 2021
How do i access the time delay fuse for a replacement?
Hi Bob,
Thank you for your question. This part is located on the inside of your machine in the top. You would have to remove your vent grille and then a second metal grille to get at the part. However you have to be very careful. Unplug your appliance and make sure to safely discharge the capacitor in your microwave. If you do not safely discharge it, it could give you a serious electric shock. I hope that helps. Good luck with your repair.
Was this helpful?
Thank you for voting!
James - For model number LMV1813ST
November 25, 2022
How do you discharge the capacitor when changing the fuse
Hi James, thank you for reaching out. You can discharge a capacitor using a screwdriver with an insulated handle, essentially you touch the tip to a capacitor and drag it slowly towards the one across from it. This creates a short circuit that results in the electricity being discharged. You may need to do this multiple times. If it is successful, you will hear a pop when the short circuit is completed. It is pretty loud, so don’t be surprised. Once this short circuit is done, it is now as safe to work on your microwave.
We hope this helps!
Was this helpful?
Thank you for voting!
Steve - For model number LMV1813ST
December 3, 2019
Problem is as if no power to unit yet the outlet the unit is plugged into has power. Control panel does not light up and does not respond at all. Prior to this the unit has worked perfect for 8 years.
Hello Steve and thanks for writing.
It sounds like a faulty fuse PS3522741 and/or capacitor PS3517241 check and replace if needed. We hope this helps. Please contact us anytime.
Hello Margie Thank you for contacting us. We have researched the model you have provided and have found the part you are looking for is PartSelect Number PS3532097. We hope this helps!
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Microwave would not rotate or heat up food.
52 of 77 peoplefound this instruction helpful.
Joshua from WHITE LAKE, MI
Very Easy
15 - 30 mins
Screw drivers
After watching a few youtube videos, I used a phillips SD to take controll pannel off to access the switches that sense when microwave door is closed. Swapped out all 3 switched and mocrowave works like new. $20 fix (shipping included)
Broken door micro switch. (unit does not start heating)
37 of 68 peoplefound this instruction helpful.
JAMES from BILLINGS, MT
Very Easy
30 - 60 mins
Screw drivers
Unplug the unit before servicing. Need phillips screwdriver. Open door. Use step ladder to access and remove 2 small screws from top of the room air diffuser at top of unit. Slide diffuser slightly to the left to align the diffuser's plastic tab on the left side to rotate toward you. (The wires for the front control panel are at the far l
... Read moreeft side of this difuser, but difuser is slotted for easy removal). Once the difuser is removed you will see 1 screw at the top that secures the pannel cover on the left side of the unit. Remove screw and slide this panel slightly up and out. This exposes the plastic frame that holds the upper and lower door switches. To locate the door switches and observe how they work, close and open the door and watch the door (bayonets) open and close the micro switches. Do the (red) buttons on top of the switches move up and down when the door bayonets push and release? If the buttons do not "pop" up when opened the switch is defective. The switch frame is secured with 2 screws. Remove screws and rotate the unit out for easy access to the micro switch(s). The internal (spring?) on my unit that is suposed to allow the red (visible) button on top of the switch to "pop" up when the door is opened was broken. Carefully pry the switch outward while being careful to lift the plastic holder-piece that holds the switch in place. Be careful, there is a small pin on the frame, so rotate the switch OUT toward you while lifting (carefully) the plastic holder-piece (you will see it on top of the switch). You can use an ohm meter to test the continuity of the switches. But if the buttons don't "pop" they are defective. Replace switch and reassemble.
Read less
Was this helpful?
Thank you for voting!
Microwave would not power up.
15 of 26 peoplefound this instruction helpful.
Dusty from SNOWMASS VLG, CO
Easy
15 - 30 mins
Screw drivers
Fun and easy fix for my kids.
The countdown timer was working but no "cooking" happening. Did not hear the familiar sound of the heating part working.
Determined it might be some simple switches for under $15 dollars. Bought one of each. They allow the microwave to turn on/activate by signaling that the door is prop
... Read moreerly latched. My wife noticed that it was failing and then failed over the course of about a day. Several times where it worked, then did not work. The timer was counting down one time and then when she opened the door the microwave heating component turned on. Guess it had activated the switch as she was opening the door.
Procedure to repair - Unplug - Remove two screws on front top - allows you to remove the vent. Realized there was a charcoal filter there that I had never replaced so ordered that after the fix. - Remove two screws to pull off the front right panel (area where your microwave buttons are) One at the top under the before mentioned vent and one under the microwave on the far right corner. - Have someone hold the panel because wiring is to short to place it on a ledge while connected or take a picture and remove connections. I simply held it while my daughter undid the micro switches. - Carefully remove micro switches. There were two "orange" button ones so I chose the top one to replace along with the green button one that I had ordered, so I simply pulled an orange from the bottom and a green from the top latch area. You may have remove the part that holds the switches since it was a little tough with the wires in the way and not knowing how the switches stay put. - plug in new switches and place in the brackets that hold them in place - reverse everything you did. Viola - a working microwave vs purchasing a brand new for several hundred dollars or having to call in a technician.I love that my young kids did this project with me and we actually got it running. Don't like to have to throw away more items at the landfill.