Restore visibility in the microwave cavity or over the cooktop with this replacement incandescent lamp. The 30 watt bulb uses a screw base to connect to the light socket and provides illumination when the appliance lighting is activated. A burned out filament may leave the area dark while the microwave continues operating normally. Replac...Read moreing a failed bulb restores light for checking food or viewing the cooking surface below. Disconnect power, allow the lamp to cool, and follow the appliance instructions for access to the bulb. This is an OEM part sourced directly from the manufacturer.
This is a single grease filter manufactured for a microwave. The microwave grease filter filters the exhaust air and traps any grease flowing out of the appliance. It is important to keep the filter clean and intact by cleaning it regularly and replacing it when needed. A clogged air filter can cause your appliance to run inefficiently an...Read mored possibly alter the taste and smell of your food. This filter is approximately 7.5 inches wide and 5 inches deep. This part is sold separately. No tools are required for this repair, the filter simply slides in and out using the easy-pull tab on the filter.
This is the replacement charcoal filter for your microwave. It is approximately 8 inches by 5 inches. The charcoal filter removes cooking odors from the air that circulate through the microwave vent. You will likely need to replace the charcoal filter if you notice any damage to it, or if it has been in your microwave for a long time. Thi...Read mores part is sold individually and is an authentic OEM part sourced directly from the manufacturer.
This micro-switch is designed for use in your microwave. The function of this part is to monitor the door latch position and communicate to the electronic control board whether the latch is open or closed. If your microwave does not provide heat, or will not start properly, you may need to replace the micro-switch. This part is approximat...Read moreely 1 inch in length and 3/4-inch in width. It is made of black plastic with two metal prongs. This is an OEM part sourced directly from the manufacturer. This part is sold individually. Be sure to disconnect the microwave from the power source before you begin this repair.
This microwave door interlock switch responds to the door latch, helping prevent cooking operation while the door is open. Its small actuator changes the electrical contact when the door opens or closes. A worn or damaged switch may prevent the microwave from starting even when the door is fully shut. Replacing a faulty switch helps resto...Read morere proper door detection within the safety interlock system. Internal microwave components can retain a dangerous electrical charge after unplugging, so disconnecting power alone does not make them safe to handle. This is an OEM part sourced directly from the manufacturer.
This bracket holds the metal or plastic flapper that closes off the exhaust duct when the fan is not running and opens when the fan turns on. If the exhaust fan on your microwave does not appear to be working, the problem may be with the damper assembly. If the damper does not open and close easily, check for any damage to the bracket, an...Read mored replace if it is damaged or faulty. This genuine OEM exhaust damper measures approximately 12 inches long by 5 inches wide.
Exhaust air passes through this microwave vent damper when the ventilation fan runs. The metal flap opens with outgoing airflow to let steam and cooking odours enter the exhaust duct, then closes when airflow stops to help limit outside drafts. A bent, warped, or stuck flap may restrict ventilation or allow air to flow back into the kitch...Read moreen. Replacing a damaged damper helps restore free flap movement and proper exhaust operation, providing a movable barrier at the duct opening between fan uses. This is an OEM part sourced directly from the manufacturer.
Electrical overload protection comes from this microwave time delay fuse, rated at 20 amps and 250 volts. It tolerates brief startup current while opening the circuit during a sustained overload or short circuit. A blown main fuse may leave the microwave without power or prevent it from starting. The fuse cannot be reset and requires repl...Read moreacement once it opens. Internal microwave components can retain a dangerous electrical charge after unplugging, so disconnecting the power cord alone does not make internal handling safe. This is an OEM part sourced directly from the manufacturer.
Secure door closure relies on this black plastic microwave door latch hook. Installed inside the door assembly, it engages the latch openings and operates the safety interlock switches when the door closes. A cracked hook or damaged latch may prevent the door from staying shut or keep the microwave from starting. Replacing a damaged latch...Read more helps restore proper mechanical engagement and door operation. The hook moves with the door release mechanism, allowing the door to open when released and latch again when closed. This is an OEM part sourced directly from the manufacturer.
This turntable assembly, also known as a rotating ring, is a genuine OEM replacement part for your microwave. It is brown in color and about 10 inches in diameter. This part supports the glass turntable and keeps it in place. Replacing this part is very easy and requires no tools. Simply remove the glass tray, pop out the existing ring and replace with the new one.
The turntable motor coupler connects the turntable motor to the tray. If the turntable on your microwave will not rotate, you may have a faulty motor coupler. The coupler commonly has a D shaped opening that fits tightly onto the motor shaft. If it is cracked, or worn it will need to be replaced. This is a genuine OEM replacement part sourced directly from the manufacturer.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Microwave would not rotate or heat up food.
52 of 77 peoplefound this instruction helpful.
Joshua from WHITE LAKE, MI
Very Easy
15 - 30 mins
Screw drivers
After watching a few youtube videos, I used a phillips SD to take controll pannel off to access the switches that sense when microwave door is closed. Swapped out all 3 switched and mocrowave works like new. $20 fix (shipping included)
Broken door micro switch. (unit does not start heating)
37 of 68 peoplefound this instruction helpful.
JAMES from BILLINGS, MT
Very Easy
30 - 60 mins
Screw drivers
Unplug the unit before servicing. Need phillips screwdriver. Open door. Use step ladder to access and remove 2 small screws from top of the room air diffuser at top of unit. Slide diffuser slightly to the left to align the diffuser's plastic tab on the left side to rotate toward you. (The wires for the front control panel are at the far l
... Read moreeft side of this difuser, but difuser is slotted for easy removal). Once the difuser is removed you will see 1 screw at the top that secures the pannel cover on the left side of the unit. Remove screw and slide this panel slightly up and out. This exposes the plastic frame that holds the upper and lower door switches. To locate the door switches and observe how they work, close and open the door and watch the door (bayonets) open and close the micro switches. Do the (red) buttons on top of the switches move up and down when the door bayonets push and release? If the buttons do not "pop" up when opened the switch is defective. The switch frame is secured with 2 screws. Remove screws and rotate the unit out for easy access to the micro switch(s). The internal (spring?) on my unit that is suposed to allow the red (visible) button on top of the switch to "pop" up when the door is opened was broken. Carefully pry the switch outward while being careful to lift the plastic holder-piece that holds the switch in place. Be careful, there is a small pin on the frame, so rotate the switch OUT toward you while lifting (carefully) the plastic holder-piece (you will see it on top of the switch). You can use an ohm meter to test the continuity of the switches. But if the buttons don't "pop" they are defective. Replace switch and reassemble.
Read less
Was this helpful?
Thank you for voting!
needed grease filters for a used over range microwave
26 of 58 peoplefound this instruction helpful.
tony from kewanna, IN
Really Easy
Less than 15 mins
ordered on the part select web site, came quickly, order was correct