LM2155 (2011-11) Jonsered Lawn Mower - Overview

This is a genuine OEM sourced replacement part is used with walk behind lawn mowers. This is the drive wheel which has plastic gears on the inside. It is designed to be driven by a pinion gear which is sold separately. If the wheel is broken or damaged it should be replaced to ensure smooth ride and consistent cut of the grass. Includes one (1) plastic wheel.

The Dust Shield is a 6-3/4 inch, black plastic part, used to prevent dust or debris fouling the wheel or axle. It attaches inside of the wheel around the axle. Installation is rated as "Easy" and will require a wrench. If broken, damaged, or worn due to fatigue, you will see visable damage and you may have debris getting caught in the axl...Read moree. If broken, replace it. Refer to your make, model and diagram to make sure you're choosing the right part. This part comes individually sold.

It is a genuine OEM supplied item which is made for walk-behind lawn mowers. This is a high-quality replacement for a missing or a damaged pinion gear that helps to drive the mower's wheel. Unfortunately, over time due to friction, the teeth on the gear may wear out. If this happens it will no longer engage the wheel and the mower will no...Read moret move. To ensure the exact location and the correct installation of the new part, refer to the diagrams of your specific model. Note, one durable metal pinion is included. You will need a wrench set and pliers to remove the old pinion and secure the new one.

Made of high-quality metal, this hex flange locknut is designed for use with various lawn mowers and ride-on mower/tractor models and is sold individually. This locknut attaches to the end of the carriage bolt and is an important component to the axle assembly. This locknut has a 3/8-inch inner-diameter and is 16 threads-per-inch. To repl...Read moreace this locknut, you will need a wrench, and if there are multiple locknuts on your equipment, they may all need to be replaced.

The E-Ring 7/16 is a 7/16-inch silver, metal part which can be attached to various locations on a variety of equipment to snap into grooves and secure parts into place. This part will require pliers to install. If broken, damaged or worn, there may be a problem with the part it is securing and the part should be replaced. Refer to your make, model and diagrams to check if this is the right part.

This part has been sourced from the original manufacturer and is intended to be used with walk-behind lawnmowers from Husqvarna, Poulan, Weed Eater, and Jonsered. The metal pawl is used to secure the pinion to the transmission axle to allow the two parts to rotate in unison. This drive pawl is priced as a single item, please note two may be needed.

This washer is not part of a kit or assembly. It is sold individually. With an O.D. of 1 inch, this OEM replacement part is made of dark grey metal and is used to provide a tight seal between the mower blade and the blade bolt/screw. This part should be replaced if you notice any visible wear, warping, or damage. You will need a wrench or socket set to complete this repair. Customers rate this repair as Easy.

This is an authentic OEM part for use with Poulan, Husqvarna, Weed Eater, Troy-Bilt.and Jonsered Lawn Mowers. The ground drive belt connects the engine crankshaft to the transaxle pulley to drive the rear wheels. If the belt breaks, the lawn tractor won't move. If the belt is worn, the lawn tractor moves sluggishly because the belt slips ...Read moreon the pulley. This part is sold individually. The tool that you will need to replace the ground drive belt is a socket set.

This authentic item is supplied by the original equipment manufacturer for use with Husqvarna walk-behind lawn mowers. It provides an identical replacement for a missing or a faulty wheel and tire assembly that was installed on a new unit. Please make sure to check the owners manual and the appropriate diagrams of your model for the corre...Read morect location and application of this component. Keep in mind this high-quality assembly is made of durable plastic and is sold individually. Note, the hardware to secure it is sold separately.

This is a genuine Craftsman selector knob that is specifically made for use with a walk behind lawn mower. This selector knob attaches to the adjustment lever giving the user a comfortable grip when adjusting the mower deck to the desired cutting height. This part is made of a durable plastic and is sold individually.

This manufacturer certified 1/4 Hex Nut can be installed using a wrench or socket and is used to secure parts in place and spead the load. If the part being secured seems loose, check this nut and replace it if broken or missing. Refer to your make, model and diagrams to ensure this is the right part for you.

This is a genuine OEM replacement part used on a variety of Lawn and Garden Equipment. This part is made out of Metal and it is Sold Individually. This steel washer has several applications based on your unit. Please refer to diagrams for proper application.