LM2153 (2013-10) Jonsered Lawn Mower - Overview

This is a genuine OEM sourced replacement part is used with walk behind lawn mowers. This is the drive wheel which has plastic gears on the inside. It is designed to be driven by a pinion gear which is sold separately. If the wheel is broken or damaged it should be replaced to ensure smooth ride and consistent cut of the grass. Includes one (1) plastic wheel.

The Dust Shield is a 6-3/4 inch, black plastic part, used to prevent dust or debris fouling the wheel or axle. It attaches inside of the wheel around the axle. Installation is rated as "Easy" and will require a wrench. If broken, damaged, or worn due to fatigue, you will see visable damage and you may have debris getting caught in the axl...Read moree. If broken, replace it. Refer to your make, model and diagram to make sure you're choosing the right part. This part comes individually sold.

This Handle Bolt is sourced directly from the original equipment manufacturer for use in various lawn and garden equipment. It is used to secure the upper and lower handles together and is tightened by a knob on the other end. It is made of metal, is black, and is sold individually, not as part of a kit or assembly. This part will need ...Read moreto be replaced when it is worn or damaged and can no longer secure the arms together. No tools are needed to complete this repair. Customers rated this repair as Easy.

This genuine replacement part is sourced directly from original manufacturer. It is used on a variety of lawn mowers. This is the knob that helps to secure the upper handle. It is made out of plastic and it is sold individually. When replacing this know you will need a screwdriver for the screw securing the knob.

It is a genuine OEM supplied item which is made for walk-behind lawn mowers. This is a high-quality replacement for a missing or a damaged pinion gear that helps to drive the mower's wheel. Unfortunately, over time due to friction, the teeth on the gear may wear out. If this happens it will no longer engage the wheel and the mower will no...Read moret move. To ensure the exact location and the correct installation of the new part, refer to the diagrams of your specific model. Note, one durable metal pinion is included. You will need a wrench set and pliers to remove the old pinion and secure the new one.

Made of high-quality metal, this hex flange locknut is designed for use with various lawn mowers and ride-on mower/tractor models and is sold individually. This locknut attaches to the end of the carriage bolt and is an important component to the axle assembly. This locknut has a 3/8-inch inner-diameter and is 16 threads-per-inch. To repl...Read moreace this locknut, you will need a wrench, and if there are multiple locknuts on your equipment, they may all need to be replaced.

The E-Ring 7/16 is a 7/16-inch silver, metal part which can be attached to various locations on a variety of equipment to snap into grooves and secure parts into place. This part will require pliers to install. If broken, damaged or worn, there may be a problem with the part it is securing and the part should be replaced. Refer to your make, model and diagrams to check if this is the right part.

This part has been sourced from the original manufacturer and is intended to be used with walk-behind lawnmowers from Husqvarna, Poulan, Weed Eater, and Jonsered. The metal pawl is used to secure the pinion to the transmission axle to allow the two parts to rotate in unison. This drive pawl is priced as a single item, please note two may be needed.

This control cable is a high quality item designed for Husqvarna walk-behind lawn mowers. It is a genuine OEM supplied replacement part, not an aftermarket imitation. This cable consists of a metal rubber insulated wire cable with z-type bent ends and it is sold individually. The control cable stops the blade when the control handle is re...Read moreleased on walk-behind mowers. If the cable is broken it will cause the brake to not release even when the lever is pressed. You may need pliers to complete this repair.

This washer is not part of a kit or assembly. It is sold individually. With an O.D. of 1 inch, this OEM replacement part is made of dark grey metal and is used to provide a tight seal between the mower blade and the blade bolt/screw. This part should be replaced if you notice any visible wear, warping, or damage. You will need a wrench or socket set to complete this repair. Customers rate this repair as Easy.

This deflector shield torsion spring is an original part from Craftsman for lawn mowers, rotary mowers, and gas walk behind lawn mowers. This part connects to the hinge rod and allows the shield to hinge down and up. You will need pliers to replace this part. This deflector shield torsion spring is made of metal and sold individually.

This replacement clipping deflector is a genuine OEM sourced replacement part that is specially designed for use with Husqvarna walk-behind lawn mowers. It is mounted to the side of the mower deck for the cut grass to be expelled out of it. This part is made from durable high quality plastic and it is sold individually. Please note the hardware to secure it is sold separately.