LHS-3050 (After S/N 001001) Echo Hedge Trimmer - Overview

This Genuine OEM air filter is a critical component designed to protect your engine by preventing dirt, dust, and other small particles from entering the carburetor and causing internal damage. Sold individually, this high-quality filter features a double-layer construction that enhances filtration efficiency and ensures optimal airflow. ...Read moreOver time, filters can become clogged with debris, restricting air intake and reducing engine performance. For best results, this type of filter should be replaced—not cleaned—once it becomes dirty. Regular replacement helps maintain engine health and ensures reliable operation of your outdoor power equipment.

This Primer Bulb is a clear, plastic, individually sold part with an Outer Diameter of 0.720 inches (18.30 mm) and a Height of 0.674 inches (17.12 mm). With Flange: 0.842" (21.40 mm). This part is rated as Easy to install by customers, and attaches to the primer pump assembly. If the part shows signs of breakage, such as cracks appearin...Read moreg due to the bulb drying out, or fatigue, then it must be replaced. Refer to your owners manual/model number to ensure you are choosing the correct part.

This OEM Fuel Filter is a silver and white, steel/felt, part measuring about 1.25 inches in length and 3/4 inch wide. It can be installed with pliers and is rated as Easy to install by customers. This part attaches inside the fuel tank to clean the fuel of debris, and should be replaced during regular maintenance, check your manual for ...Read morerecommended replacement time. If the filter is leaking or it has a blockage preventing fuel flow, then it should be replaced. If the engine sounds like it is not getting enough fuel, then remove the filter and check it for blockage.

This a a genuine OEM replacement check valve for your small engine. It is also known as a fuel tank vent. You may need to replace this part if you are noticing debris or dirty oil in the reservoir. Make sure the engine is cool before you begin this repair, and remove the wire and boot from the spark plug to prevent the engine from starting up.

This part is the fuel return tube for your outdoor power equipment. It is made of yellow plastic and measures 3x6x110mm. The return tube transports excess fuel back into the fuel tank after the primer bulb has been pressed and has primed the carburetor so the engine can start. Over time, this fuel tube can crack or clog, and this can caus...Read moree problems for the engine. To replace this part, carefully pull the tube off the carburetor and the fuel tank, then connect the new tube. This part is sourced directly from the manufacturer and is an OEM part. It is sold individually.

This is a genuine manufacturer approved replacement part designed for use with edgers and trimmers. The purpose of this part is to act as a seal for the insulator. This item is made out of compound material and it is sold individually. To complete this repair you would need a screwdriver.

Also referred to as a Spark Arrester, this Spark Arrester Screen is an authentic OEM replacement part that is not part of a kit or assembly. It is made of metal and sold individually. The purpose of this screen is to prevent flammable debris from entering the engine and becomes worn through regular use. If the screen is clogged, remove th...Read moree screen from the muffler, hold it with pliers, and use a torch to burn off the debris before reinstalling the screen. This part needs to be replaced when it becomes damaged or worn. When the screen is malfunctioning, you may notice debris exiting through the muffler. To complete this repair, you will need a screwdriver and pliers. This screen is located within the muffler; refer to your owner's manual for the exact location on your model. Customers rated this repair as Easy.

Genuine OEM replacement part, this item is sold individually. The purpose of the part is to cover the air filter on the outdoor products shown below. It helps keeping larger pieces of debris from coming in contact with the air filter. While providing enough clearance for air to enter the carburetor through the air filter and mixing with the fuel to make the unit run properly.

This OEM nut is a 5mm, gold, metal nut, which is sold individually. It can be installed with a Wrench or Socket and Torque Wrench by torquing to the manufacturer specifications. This nut is used to secure another part in place, and should be replaced if damaged due to fatigue (such as damaged threads or rounded ends). This nut can have v...Read morearious uses on various equipment, and as such the difficulty of the installation can vary, but generally this is an easy repair.

This is a genuine OEM sourced replacement part designed for use with Echo blowers/trimmers. This is a standard hardware which has multiple applications based on your unit. Please refer to diagrams for proper application. This screw is made out of metal and it is sold individually. To remove or install this screw you would need a screwdriver.