LGB336GET1WH General Electric Range - Overview

Sections of the LGB336GET1WH

[Viewing 4 of 4]
Keep searches simple, eg. "belt" or "pump".
Round Style Oven Igniter – Part Number: WB2X9154
Round Style Oven Igniter
★★★★★
★★★★★
(60)
PartSelect #: PS243425
Manufacturer #: WB2X9154
The round style oven igniter is also known as an oven bake or broil igniter and is compatible with your range appliance. The function of the round style oven igniter is to pull electrical current thro...
$117.09
  In Stock
Light Bulb - 40W – Part Number: 40A15
Light Bulb - 40W
★★★★★
★★★★★
(8)
PartSelect #: PS217532
Manufacturer #: 40A15
This 40-Watt light bulb is sold individually and is a genuine OEM replacement option for your home appliances. It is specially designed to withstand extreme temperatures, so this bulb is compatible wi...
$11.01
  In Stock
Oven Rack – Part Number: WB48T10095
Oven Rack
★★★★★
★★★★★
(17)
PartSelect #: PS6447646
Manufacturer #: WB48T10095
The oven rack is sold individually. It is chrome in color and measures approximately 24 inches wide by 17-1/2 inches deep. The rack is used to hold cookware in the oven and slides back and forth for e...
$67.36
  In Stock
Ignitor Mounting Screw – Part Number: WB1X1293
Ignitor Mounting Screw
★★★★★
★★★★★
(2)
PartSelect #: PS234519
Manufacturer #: WB1X1293
Sold Individually.
$9.63
  In Stock
RECEPTACLE PUSH-IN – Part Number: WB08T10026
RECEPTACLE PUSH-IN
★★★★★
★★★★★
(7)
PartSelect #: PS752188
Manufacturer #: WB08T10026
This part is the replacement light socket for your oven. The oven light socket provides power to the light, and at the same time holds the light bulb in place.
$8.54
  In Stock
SCREW – Part Number: WB1K5062
SCREW
PartSelect #: PS234148
Manufacturer #: WB1K5062
$11.58
  In Stock
Light Cover – Part Number: WB36X192
Light Cover
★★★★★
★★★★★
(8)
PartSelect #: PS247415
Manufacturer #: WB36X192
This light bulb lens covers the interior light bulb in an oven, range, or stove. No tools are necessary to replace this part. Simply slide off the wire bracket to remove the existing light bulb lens. ...
$13.52
  In Stock
Screw – Part Number: WR01X10065
Screw
★★★★★
★★★★★
(1)
PartSelect #: PS283515
Manufacturer #: WR01X10065
Size: 10-32 GXTT FLP .595 Sold individually.
$8.06
  In Stock
Burner Spark Module - 120V 60Hz – Part Number: WB13K25
Burner Spark Module - 120V 60Hz
★★★★★
★★★★★
(3)
PartSelect #: PS231281
Manufacturer #: WB13K25
This part sends enough current to the igniter to create a spark to the bottom of the burner cap.
  No Longer Available
Door Gasket – Part Number: WB4K1
Door Gasket
★★★★★
★★★★★
(4)
PartSelect #: PS250264
Manufacturer #: WB4K1
$52.03
  In Stock
Oven Door Bottom Trim - Black – Part Number: WB07K10232
Oven Door Bottom Trim - Black
★★★★★
★★★★★
(5)
PartSelect #: PS2321142
Manufacturer #: WB07K10232
$24.47
  In Stock
Burner Head - Large – Part Number: WB29K25
Burner Head - Large
PartSelect #: PS241290
Manufacturer #: WB29K25
$87.13
  Special Order

Questions And Answers for LGB336GET1WH

Be the first to ask our experts a question about this model!

Common Symptoms of the LGB336GET1WH

[Viewing 6 of 6]
Will Not Start
Fixed by
these parts
Fixing Fixing
Show All
Little to no heat when baking
Fixed by
these parts
Fixing Fixing
Show All
Gas igniter glows, but will not light
Fixed by
these parts
Fixing Fixing
Show All
Element will not heat
Fixed by
these parts
Fixing
Show All
Little to no heat when broiling
Fixed by
these parts
Fixing
Show All
Oven not heating evenly
Fixed by
these parts
Fixing
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
No ignition
Unplug the oven.
Open the oven door.
Remove the racks.
Remove the two screws that hold the oven floor; they are located toward the back.
Remove the oven floor pan.
Remove the screw holding the heat shield/dispenser.
Remove the heat shield/dispenser.
Untwist the ceramic wire caps on the two igniter wires.
Remove the two screws holding the igniter.
Remove the igniter.
Replace the igniter working all the steps backwards.
It’s super simple.
Parts Used:
Round Style Oven Igniter
  • Mark from Upland, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
765 of 831 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broiler works, bake oven does not work.
Your website help me troubleshoot the problem and locate the part. Part was delivered the next day. Following the instructions that others on your website had provided, the repair was quick and SUCCESSFUL.
Gas will not flow if the igniter is bad. Gas will only flow if the igniter heats up the internal bimetal strip which in turn, allows gas to flow through the safety valve
First, unplug the power sourse. For this repair it is not necessary to shut off the gas, but do so if it makes you more comfortable. Remove the oven door...it lifts right off. Next, remove the screws and lift out the bottom panel in the oven box. This will expose the igniter. Next, remove the lower drawer. Two 1/4-28 screws retain the igniter...remove these. With the drawer removed, go underneath and locate the 2 wires to the igniter. One has a green connector, and the other has a red connector. Disconnect these 2 wires and carefully remove the igniter and wires. Cut the wires from the igniter on the igniter end. You will need to reuse the plug end of each wire, so don't cut them too short. Splice these two wires to the new igniter with the wire splice caps provided. Feed the wires back down throught the opening at the back of the oven and carefully move the igniter into place. Install the two 1/4-28 retaining screws. Go back underneath the oven through the drawer opening and plug in the 2 wires. You should be good to go. Reassemble the oven and have mama bake a cake..
Parts Used:
Round Style Oven Igniter
  • Robert from Hebron, CT
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers, Socket set, Wrench set
600 of 783 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven igniter failed to heat up and ignite the gas burner.
Before starting it's a good idea to disconnect the electricity and turn the gas valve off behind the stove.

Next, uncrew the two finger-screws at the back of the oven that hold the porcelain & steel drip plate in. It comes out if you push it towards the back of the oven and lift it out. This reveals the burner and the cylindrical igniter attached to the side of the burner. While I was there I unscrewed the one screw at the front end of the burner (nearest me).

After attempting the repair from inside the oven, I realized it was far easier to pull out the bottom drawer and work from under the oven instead. Using only one size mini-socket for all screws it was easy. I undid the two screws that hold the main burner to the back of the oven. This allowed me to pull the burner up inside the oven so I could access the screws that held the igniter to the side of the burner. A flashlight helps when working under the oven.

Under the oven again I then pulled the two wires off their respective connectors. Then inside the oven unscrewed the two screws holding the igniter to the burner. The old part came off very easily. However, the new part didn't have connectors attached, so I had to remember which wire went where and cut the old connectors off and splice them to the new. Be sure to leave yourself as much of the old wire as possible attached to the connector. Otherswise you might find the "new" wires too short to reach the connectors.

I reconnected the igniter to the main burner with the two screws. Then fed the burner and wires back into place. I then lightly screwed the single front screw on the burner (inside the oven) to help position the burner, then went underneath to install the other two screws.

Under the oven I made sure the wires fit onto their connectors then tightened the two screws to hold the burner to the back wall. Once the burner was properly in place I tightened the two screws and the single one inside the oven.

I then plugged the oven back in and turned on the gas flow. I turned the oven dial and watched the new igniter glow wonderfully.

Finally I replaced the porcelain floor cover inside the oven. These finger screws can be a bit tricky because they go into a threaded clip that might have moved while you worked. The whole task took less than 30 minutes - and I had never done this before.
Parts Used:
Round Style Oven Igniter
  • Paul from Santa Rosa, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Socket set
355 of 517 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!