This front plate assembly, also known as a mullion or flipper, is a genuine replacement part designed for select LG and Kenmore French-door refrigerators. It serves a critical function by sealing the gap between the doors, preventing cold air from escaping and helping maintain consistent internal temperatures. Constructed from durable pla...Read morestic, it supports both the performance and appearance of the appliance. A failing mullion may result in poor sealing, visible gaps, increased energy consumption, and potential food spoilage. Replacing this component can restore proper door alignment and improve overall efficiency. Compatibility should be confirmed using your refrigerator’s model number prior to installation.
The door stop, or door stopper, is used in refrigerators. This door stop helps keep the door in position and in balance. This part is attached to the bottom of the door and it keeps it from opening and hitting the side of the refrigerator cabinet. If you find your door hits and scratches your lower cabinet when you open your fridge door, ...Read moreinstalling this part can be a solution to this problem. Make sure to unplug your appliance from the power source before installing this part and safely store food to prevent it from deteriorating. Refer to the diagram provided by the manufacturer for further instruction.
This is a drawer roller for the freezer compartment of your LG refrigerator. This roller is made of white plastic, and acts as a wheel to allow the drawer to glide smoothly back and forth when you open and close the freezer compartment. Over time and with further frequent use, this roller can crack, break, or stop rolling smoothly, at whi...Read morech point it will need replacing. Your refrigerator comes with two rollers, and this roller is sold individually, so consider how many rollers you require before ordering.
This deli drawer is for refrigerators. Deli drawer holds meats, vegetables and snacks in the fresh food compartment of the refrigerator. Follow the instructions in the owner's manual when installing this part.
This genuine refrigerator ice storage container holds and stores ice produced by the ice maker until it is ready to be dispensed. Featuring an integrated auger and dispensing mechanism, it helps deliver ice smoothly through the refrigerator door while keeping ice organized and readily available. Designed as a direct replacement for a dama...Read moreged or worn ice bucket, it can help restore proper ice dispensing performance. The container measures approximately 15 inches long, 8 inches wide, and 7 inches high.
This is a single water filter that can be accessible inside the refrigerator. Water filters are designed to provide cleaner and betting tasting water, while also protecting refrigerators and ice machines from sediment deposits. Simply twist and turn to remove and replace. Recommended to replace every 6 months.
This is a door gasket for the right side of various models of LG refrigerators. Door gaskets, also known as seals, are used to create a barrier between the outside ambient temperature of your home and the cool-controlled internal temperature of the refrigerator. If your refrigerator door seal is warped, cracking, or damaged in any way, it...Read more is important to replace it as soon as possible to ensure optimal cooling performance from your fridge. This is a gray-colored OEM door seal that simply needs to be wrapped carefully around the perimeter of your refrigerator door.
This is a genuine OEM evaporator motor that directly powers the evaporator mechanism within your refrigerator. This mechanism is responsible for pulling air over the evaporator coils, which are cold, and circulating that cold air back throughout the appliance. Without this motor, the interior of your refrigerator would build up frost, str...Read moreain the compressor, and simply not cool your fridge enough. A warm fridge, frost buildup or unusual noises are all signs that this fan needs replacing, and over time or through excessive dust building up, motor issues will arise and can cause it to fail. This fan motor is sold as an individual part, so it does not come with any securing screws or the fan blade itself. Replacing the evaporator fan motor will require your user manual and Philips-head and flathead screwdrivers. You need to gain access to the evaporator cover, which you will need to locate using your user manual schematics. Once the cover is removed and you disconnect the wire harnesses within it, you can disassemble the fan mechanism on its inside portion. With the fan mechanism disassembled, remove the old mechanism and install the new one, with the securing screws and wire harnesses.
This part must be installed by a licensed and trained LG technician that is able to perform a software update, which is required for the installation of this compressor. Part number CJT30000002 is needed to perform the update.
Also, the three pins on the side of the new compressor may be oriented differently than the original. If diff...Read moreerent, when installing the new compressor the compressor electrical connector must be rotated 45 degrees counter-clockwise.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
replace leaking water inlet valve assembly
42 of 75 peoplefound this instruction helpful.
Richard from JACKSONVILLE, FL
Really Easy
15 - 30 mins
Screw drivers
1. Shut off water to refrigerator. 2. Removed bottom sheet metal cover (6 screws). 3. Removed leaking water inlet valve assembly from refrigerator (1 screw). 4. Remove water inlet tube (loosen nut) and tube back to refrigerator (pull from water valve after remove cotter pin washer). 5. Detach two electrical wire harnesses. 6. Install new
... Read morewater inlet valve assembly to refrigerator (1 screw). 7. Replace both water tubes to water inlet assembly. 8. Re-attach both wiring harnesses. 9. Turn water to refrigerator on. 10. Check for leaks. 11. Re-attach bottom sheet cover (6 screws).
Read less
Was this helpful?
Thank you for voting!
The factory door gasket was split and needed replacing
22 of 36 peoplefound this instruction helpful.
Carl from LAKE WYLIE, SC
Very Easy
Less than 15 mins
I pulled the gasket off and installed the new one. It was very easy. All I had to do was to push the new gasket in place in the grooves in the door. The gasket I received was identical to the one I replaced.
Was this helpful?
Thank you for voting!
My nephew accidentally forced the door closed last year, which resulted in the door having to be re closed manually folding back the flap. Ugh!
25 of 46 peoplefound this instruction helpful.
Tiziana from WARWICK, NY
Really Easy
Less than 15 mins
Nutdriver
Unscered 2 screws, unplug electrical connection under the screws, slide her flap into grooves, realign screw holes , and rescrew in. Done.