EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

LFD23860SW LG Refrigerator - Overview

Diagrams for LFD23860SW

See every part. Know exactly what you need.

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Refrigerator Water Filter LT600P – Part Number: 5231JA2006F
$65.48
In Stock
Refrigerator Water Filter LT600P
★★★★★
★★★★★
(13)
Part #5231JA2006F
This refrigerator water filter is designed to improve the taste and odor of both water and ice by reducing a wide range of contaminants. Utilizing an activated carbon block filtration method, it effectively captures impurities such as lead, chlorine, mercury, cysts, asbestos, and particulates, while allowing fluoride to pass through. The filter is certified to meet NSF/ANSI Standards 42 and 53 for water purification, ensuring reliable performance and safety. With a lifespan of approximately six months or 300 gallons—depending on water quality and usage—it provides consistent filtration and supports the overall efficiency of your refrigerator’s water system.
Ice Maker Assembly – Part Number: 5989JA0002N
No Longer Available
Ice Maker Assembly
★★★★★
★★★★★
(12)
Part #5989JA0002N
This ice maker assembly is a genuine OEM replacement unit for LG refrigerators. It is responsible for producing and dispensing ice cubes. You can find the ice maker assembly inside the freezer compartment of your fridge. The assembly consists of several parts, including a water inlet valve, ice mold, thermostat, and motorized assembly for dispensing ice. If any of these components fail, your ice maker will be unable to produce any ice or may only release small amounts of ice. This complete assembly contains all the parts you need to replace your faulty unit and restore your refrigerator.
Clip – Part Number: 4004JA3002A
$31.58
Special Order
Clip
★★★★★
★★★★★
(2)
Part #4004JA3002A
This water tubing clip holds the water fill tube in place in your refrigerator. The water fill tube attaches and supplies water to the ice maker/water dispenser in your fridge-freezer. If the tubing is in working order, but is hanging loose inside the unit, the issue could be that the clip meant to hold it in place is broken. If this is the case, you should look to replace the clip. This clip is made of black plastic, and is just over half an inch long. This is a genuine OEM replacement part, and is sold separately.

Common Symptoms of the LFD23860SW

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
The rails for one of drawers were replaced
5 of 8 people found this instruction helpful.
  • Michael G, from CENTENNIAL, CO
  • Really Easy
  • Less than 15 mins
Removed old rails and tapped new rails in place. The big problem was finding how to fix the drawer. After searching many online websites, It was my good fortune to find Partselect and a one of their service representatives who
knew how to fix my drawer
and they had the part.
Was this helpful?
Thank you for voting!
icemaker stopped working
4 of 5 people found this instruction helpful.
  • Norris from Telford, PA
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
This is bottom drawer type frige. Icemaker is inside (not in the door) and hard to reach. I first tested the solenoids by disconnecting them and using a test cord, energized them independent of the frige wiring. They worked ok. Note: this frige has (2) solenoids going to the icemaker. And it has (3) solenoids serving the water disp enser. The icemaker solenoids are wired in parallel. I removed the icemaker by removing (1) screw from the bottom and loosening (2) on the top. Then removed icemaker as a complete unit disconnecting the wire connector at the same time. On the bench I tested the icemaker to verify it was defective. The wire harness has a 10 amp fuse in the black wire (hot wire). `The fuse was blown. This was sufficient to indicate the icemaker is shot. I did however, do some other tests. Cold resistance of the mold heater was 72 ohms. The timer motor was 4000 ohms. These measurements should be ok. I then activated the icemaker with a test cord, bypassing the blown fuse. The unit cycled one complete rotation then stopped. The mold heater worked. I tested the amp draw on the mold heater and it was only .1 amps. I should be a about .8 amps. I then cycled it again and then the timer motor began to sizzle and smell. Then it smoked and stopped mid-rotation. I then purchased a new icemaker. I believe the mold heater was going bad over time as this unit made ice but very slowly. This put extra strain on the motor as the mold was not releasing quickly. This damaged the motor causing it to fail.
Was this helpful?
Thank you for voting!
The water filter needed to be replaced.
1 of 3 people found this instruction helpful.
  • Alice from Wimberley, TX
  • Really Easy
  • Less than 15 mins
I screwed the old one out and replaced it with the new one. A no-brainer. The thing that was so amazing was that I ordered the filter on the intrnet and it arrived the very next day!!! I was very surprised and pleased with the very quick shipping!!!
Was this helpful?
Thank you for voting!