This handle screw, also known as a mounting bolt, is a mounting screw to help secure the door handle to your refrigerator door. If your handle is loose, you may just need to tighten the screw. If your screw is missing or broken, it may need to be replaced. There are multiple handle screws on your fridge, please consider ordering extra as ...Read morethey commonly wear at the same rate. This is about 1 inch long and metallic in color.
The door stop, or door stopper, is used in refrigerators. This door stop helps keep the door in position and in balance. This part is attached to the bottom of the door and it keeps it from opening and hitting the side of the refrigerator cabinet. If you find your door hits and scratches your lower cabinet when you open your fridge door, ...Read moreinstalling this part can be a solution to this problem. Make sure to unplug your appliance from the power source before installing this part and safely store food to prevent it from deteriorating. Refer to the diagram provided by the manufacturer for further instruction.
The purpose of the door latch cam is to keep the door latched when you shut it. If your door is not staying shut, you may need to replace the door latch cam. This part is made of white plastic and is about 2 inches in length. The door latch cam is located at the top of the door, and you will need to remove the trim that covers the gasket ...Read morein order to access the door latch cam. To complete this repair, you will need a flat blade screwdriver to pop out the plastic tabs holding the gasket in place. This part is sold individually.
This ice maker assembly is a genuine OEM replacement unit for LG refrigerators. It is responsible for producing and dispensing ice cubes. You can find the ice maker assembly inside the freezer compartment of your fridge. The assembly consists of several parts, including a water inlet valve, ice mold, thermostat, and motorized assembly for...Read more dispensing ice. If any of these components fail, your ice maker will be unable to produce any ice or may only release small amounts of ice. This complete assembly contains all the parts you need to replace your faulty unit and restore your refrigerator.
This genuine OEM water valve controls the flow of water to the ice maker and water dispenser of your refrigerator. It opens to allow water into the designated compartments and closes once the desired amount has been dispensed or the ice tray is filled. If it is broken, you might experience issues like no ice production, a non-functioning ...Read morewater dispenser, or leaks at the back of the fridge. Connecting the water inlet valve is easy, just snap the inlet valve wires into the wire connector.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
icemaker stopped working
4 of 5 peoplefound this instruction helpful.
Norris from Telford, PA
A Bit Difficult
30 - 60 mins
Screw drivers
This is bottom drawer type frige. Icemaker is inside (not in the door) and hard to reach. I first tested the solenoids by disconnecting them and using a test cord, energized them independent of the frige wiring. They worked ok. Note: this frige has (2) solenoids going to the icemaker. And it has (3) solenoids serving the water disp
... Read moreenser. The icemaker solenoids are wired in parallel. I removed the icemaker by removing (1) screw from the bottom and loosening (2) on the top. Then removed icemaker as a complete unit disconnecting the wire connector at the same time. On the bench I tested the icemaker to verify it was defective. The wire harness has a 10 amp fuse in the black wire (hot wire). `The fuse was blown. This was sufficient to indicate the icemaker is shot. I did however, do some other tests. Cold resistance of the mold heater was 72 ohms. The timer motor was 4000 ohms. These measurements should be ok. I then activated the icemaker with a test cord, bypassing the blown fuse. The unit cycled one complete rotation then stopped. The mold heater worked. I tested the amp draw on the mold heater and it was only .1 amps. I should be a about .8 amps. I then cycled it again and then the timer motor began to sizzle and smell. Then it smoked and stopped mid-rotation. I then purchased a new icemaker. I believe the mold heater was going bad over time as this unit made ice but very slowly. This put extra strain on the motor as the mold was not releasing quickly. This damaged the motor causing it to fail.
Read less
Was this helpful?
Thank you for voting!
The part did not fit
2 of 2 peoplefound this instruction helpful.
Stacy from ST AUGUSTINE, FL
Really Easy
30 - 60 mins
Like the customer who put a review on your site before me, I was unable to complete the repair because the inlet tube did not fit my refrigerator. I was hoping to speak to someone regarding this issue.
The past I ordered was broken upon delivery. I asked for a replacement and was refunded the charge. Tried to contact you but "due to covid" you aren't taking calls. Net result: I ordered the part from another source, got it, installed easily. Won't use you again.