This dishwasher door hinge cable assembly connects the door to the spring. The door hinge cable and the door spring apply tension to the door to prevent it from dropping open too quickly. This part contains two plastic pieces which are approximately 2 inches in length by 3/4-inch in width, as well as a rope portion that measures approxima...Read moretely 8 inches in length. When beginning this repair, be sure to use caution when replacing the door hinge cable. The spring to which the door hinge cable attaches is under tension and could snap. This part is sold individually.
The dishwasher roller assembly connects to the dishrack, and is located in the lower level of the dishwasher. It allows the dishrack to easily slide in and out. If the lower rack keeps falling off the track in your dishwasher, makes noises, the door will not close, or the dishes are not getting clean, then it is best to replace it for mor...Read moree security. A flat blade screw driver is the only tool needed for this installation. Open the lower dishwasher rack and remove retaining tabs from both ends of the rack and slide it out. Locate the older roll assembly, remove it and replace the rollers. Remember to put the tabs on each side back before sliding it back in. Make sure the dishwasher is off before starting this installation project.
The rack roller and axle in your dishwasher allows the dish rack to slide in and out effectively.If you notice that your dish rack is not performing this function, or if one or more of your rack rollers are damaged, you should consider replacing it. The roller attaches to the dish rack with the axle, both are included in this part. This p...Read moreart is gray in color, and measures 1 inch in diameter. With the axle, this part is approximately 1-1/2 inches wide. To access the rack roller and axle, you will need to remove the top dish rack from your dishwasher.
The door spring, used in dishwashers, adds tension to the door through the door hinge to keep it from opening too fast. If you have a door latch failure or your washer door drops too quickly when opened, it is best you replace this part to fix the problem. Refer to the manual provided by the manufacturer for installation instructions and ...Read morefurther repair guidance. Unplug your dishwasher from the power source before you begin this repair project as a safety precaution.
This dishwasher door gasket is designed to form a secure, watertight seal around the tub, preventing leaks and enhancing overall wash efficiency. Constructed from flexible, heat-resistant black rubber, it withstands temperatures up to 150°F and resists wear over time. By maintaining a tight seal, the gasket ensures that water and steam re...Read moremain contained within the dishwasher during operation, contributing to more effective cleaning cycles and reduced energy waste. A worn or damaged gasket can lead to water pooling, inefficient washing, and potential damage to surrounding cabinetry. Replacing it restores proper function and helps extend the appliance’s lifespan. Installation is straightforward, requiring the gasket to be pressed into the door channel for a snug fit.
This diverter motor, or stepper motor, controls the movement of the spray arms in your dishwasher. It directs water between the drain pump and the spray arms by turning a check valve inside the pump, managing the flow of water to these spray arms. This diverter motor runs on 120 volts and 60 Hz. When this motor fails, the dishwasher will ...Read morenot wash or drain properly. Please keep in mind that this genuine OEM replacement part is sold separately from the spray arms.
This is the lower dishrack assembly for various models of LG dishwashers. This dishrack is an OEM part that is designed to hold dishes and cutlery during the wash cycle of the dishwasher. This dishrack is made of a coated metal to prevent rusting, cracking, and peeling. However, over time and through further exposure to hot temperatures f...Read morerom the heating element, the coated material of the dishwasher rack can begin to peel, at which time it needs replacing. This dishrack comes as an individual part and does not come with any other parts or accessories, such as its accompanying cutlery basket.
This corrugated drain hose assembly directs wastewater from your dishwasher to the household drainage system. Positioned at the rear of the unit, it connects the pump to the sink drain or garbage disposal. If the hose becomes damaged or punctured, you may observe water leakage beneath the dishwasher or standing water within it. Please kee...Read morep in mind that this genuine OEM replacement part is sold separately from the drain pump.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Bryce - For model number LDF7561ST
August 10, 2025
The dishwasher wash cycle stops and shows an error message: "OE". I can give it a drain override command, and it will intermittently pump away the water. The drain hose seems clear, and the filters are clean. But it will not complete a cycle or pump away all the water.
Hello Bryce, thank you for getting in touch. Dishwasher displaying the "OE" error code indicates a drainage problem. The dishwasher is unable to properly drain the water used during the wash cycle. You will need to replace the drain pump, part number PS11707090, to fix the issue. We hope this helps.
The spray arm broke from the assembly, is their a replacement part?
Hi Stephen, thank you for reaching out. According to our research, your model comes with three spray arms: Upper Spray Arm, part number PS3527665, Middle Spray Arm, part number PS7788355, and Bottom Spray Arm, part number PS7788355. We hope this helps! If you need help placing an order, customer service is open 7 days a week. Thanks again for your great question.
The unit leaves about 1cup of water in the bottom after use with no alarms.
Hello Terry, thank you for getting in touch. Based on our research, we would recommend checking the drain hose for blockage. If this does not resolve the issue, then you may need to check the drain pump, part number PS11706890, to solve the problem. We hope this helps!
When the dishwasher door is opened there is a part attached to keep it from dropping
Hi Maryann, thank you for reaching out. Based on our understanding, you may need the door hinge spring, part number PS3524564. It applies tension to the dishwasher door through the door hinge to prevent the door from dropping too quickly when you open the dishwasher. We hope this information is useful!
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Broken door spring allows the door to overextend to the floor if not propped.
36 of 44 peoplefound this instruction helpful.
Gregory L from INDEPENDENCE, OH
Easy
15 - 30 mins
Screw drivers
Simple, removed screws securing machine in the cabinet, then pull the unit out of the cabinet space about 10 inches. Springs are accessible within this extension. You need strong hands to extend the springs and attach them. Once attached, push machine back in place and re-install the anchor screws. In my situation, only one spring was bro
... Read moreken, so the attached side revealed the correct slot to place the hook on the top position, the bottom position has a plastic lead for the spring, and that lead is attached to a rope to the door hinge. Note: Replace BOTH springs, even if only one is broken.
Dishwasher leaking; got AE error almost every other wash
12 of 20 peoplefound this instruction helpful.
Bruce from Katy, TX
Really Easy
30 - 60 mins
The inside gasket deteriorates over time - However replacement is easy. the main thing you have to remember is after you remove the old gasket, install the new one starting at the middle top of the tub and work your way down both sides. Also, don't push the gasket all the way in...only enough to hold in place. When you close the door the
... Read moregasket will form a better seal around the door.
My Orders
