LBB-4200 (After S/N 001001) Echo Leaf Blower / Vacuum - Overview

This Primer Bulb is a clear, plastic, individually sold part with an Outer Diameter of 0.720 inches (18.30 mm) and a Height of 0.674 inches (17.12 mm). With Flange: 0.842" (21.40 mm). This part is rated as Easy to install by customers, and attaches to the primer pump assembly. If the part shows signs of breakage, such as cracks appearin...Read moreg due to the bulb drying out, or fatigue, then it must be replaced. Refer to your owners manual/model number to ensure you are choosing the correct part.

This OEM Fuel Filter is a silver and white, steel/felt, part measuring about 1.25 inches in length and 3/4 inch wide. It can be installed with pliers and is rated as Easy to install by customers. This part attaches inside the fuel tank to clean the fuel of debris, and should be replaced during regular maintenance, check your manual for ...Read morerecommended replacement time. If the filter is leaking or it has a blockage preventing fuel flow, then it should be replaced. If the engine sounds like it is not getting enough fuel, then remove the filter and check it for blockage.

Genuine OEM replacement part, this item is sold individually. The purpose of the Retainer Cushion is to isolate the vibration of the engine from the frame of the Backpack Blowers shown below. So the user does not experience excessive vibration.

This is an authentic Echo replacement part designed for use with backpack blowers. This part interlocks with the other blower tubes that are sold separately. Over time this part can crack allowing for air leaks. This will greatly decrease blowing/suction ability of the unit, at this point part should be replaced. This tube is made out of black plastic and it is sold individually.

Genuine Echo replacement part, this item is sold individually. Two of the Backpack Harnesses are needed for the Back Pack Blowers shown below. It does include the mounting hardware to attach it to the Blower. The Backpack harness is padded for comfort when using the Blower.

This is a genuine OEM replacement part used on Echo backpack blowers. Over time this part can become brittle and crack allowing for air leaks. This will greatly decrease blowing/suction ability of the unit, at this point it should be replaced. This flexible tube is made out of plastic and it is sold individually.

This is a genuine OEM sourced replacement part designed for use with Echo blowers/trimmers. This is a standard hardware which has multiple applications based on your unit. Please refer to diagrams for proper application. This screw is made out of metal and it is sold individually. To remove or install this screw you would need a screwdriver.

This screw is supplied directly from original equipment manufacturer for use with Shindaiwa and Echo power equipment/tools. This screw is a standard hardware that has multiple uses depending on your model. Please make sure to check appropriate diagrams for correct location and application for this screw. It is made out of metal and it is sold individually. To secure/loosen this screw you would need a screwdriver.

This manufacturer approved replacement part is used on Echo backpack blowers. This part interlocks with the other blower tubes that are sold separately. Over time it can crack allowing for air leaks. This will greatly decrease blowing/suction ability of the unit, therefore this part should be replaced. This tube is made out of black plastic and it is sold individually

This spark plug wire, also known as a spark plug coil or spark plug cap coil, is compatible with various makes and models of hand-held outdoor power equipment and is sold individually. This wire is installed within the spark plug boot and attaches to the spark plug for the ignition of your equipment. The spark plug wire is often exposed t...Read moreo extreme heat and excessive vibrations, so through normal wear and tear, it will likely break down. If your equipment is having difficulty starting or has general performance issues, the wire may be the reason why. To replace this wire, make sure your equipment is off before removing the wire and boot from the spark plug. Remove the boot from the wire and install the new wire within the boot before re-installing the boot back to the spark plug.

This is an authentic manufacturer sourced replacement part designed for use with Echo backpack blowers. This carburetor gasket provides an air tight seal between the carburetor and the insulator. Over time gaskets tend to deteriorate and would need to be replaced. It is made out of compound material and it is sold individually. You would need a screwdriver to replace this item.