LBB-4000 (After S/N 001001) Echo Leaf Blower / Vacuum - Overview

This OEM Fuel Filter is a silver and white, steel/felt, part measuring about 1.25 inches in length and 3/4 inch wide. It can be installed with pliers and is rated as Easy to install by customers. This part attaches inside the fuel tank to clean the fuel of debris, and should be replaced during regular maintenance, check your manual for ...Read morerecommended replacement time. If the filter is leaking or it has a blockage preventing fuel flow, then it should be replaced. If the engine sounds like it is not getting enough fuel, then remove the filter and check it for blockage.

This is an authentic Echo replacement part designed for use with backpack blowers. This part interlocks with the other blower tubes that are sold separately. Over time this part can crack allowing for air leaks. This will greatly decrease blowing/suction ability of the unit, at this point part should be replaced. This tube is made out of black plastic and it is sold individually.

This OEM nut is a 5mm, gold, metal nut, which is sold individually. It can be installed with a Wrench or Socket and Torque Wrench by torquing to the manufacturer specifications. This nut is used to secure another part in place, and should be replaced if damaged due to fatigue (such as damaged threads or rounded ends). This nut can have v...Read morearious uses on various equipment, and as such the difficulty of the installation can vary, but generally this is an easy repair.

This manufacturer approved replacement part is used on Echo backpack blowers. This part interlocks with the other blower tubes that are sold separately. Over time it can crack allowing for air leaks. This will greatly decrease blowing/suction ability of the unit, therefore this part should be replaced. This tube is made out of black plastic and it is sold individually

This spark plug wire, also known as a spark plug coil or spark plug cap coil, is compatible with various makes and models of hand-held outdoor power equipment and is sold individually. This wire is installed within the spark plug boot and attaches to the spark plug for the ignition of your equipment. The spark plug wire is often exposed t...Read moreo extreme heat and excessive vibrations, so through normal wear and tear, it will likely break down. If your equipment is having difficulty starting or has general performance issues, the wire may be the reason why. To replace this wire, make sure your equipment is off before removing the wire and boot from the spark plug. Remove the boot from the wire and install the new wire within the boot before re-installing the boot back to the spark plug.

This OEM metal washer is commonly used on a variety of different small engine/lawn equipment models and is sold individually. This washer is used to help evenly distribute pressure from the securing bolt or screw with the cylinder cover, to reduce any effects of vibration from the engine. If the connection between the securing fastener be...Read morecomes loose, or if you are replacing the fastener itself, it is recommended that you replace this washer as well.

This replacement spark plug cap is a genuine OEM sourced item designed for use on handheld lawn and garden equipment. It is used to insulate the plug and wire terminal. Over time rubber material can dry out and crack requiring replacement. Please note, this item is sold individually.

This replacement part is an authentic OEM screw designed for use with blowers and string trimmers. This is a standard hardware which has multiple uses based on equipment. Please refer to diagrams for proper application. This screw is made out of metal and it is sold individually. To secure or loosen this screw you would need a phillips head screwdriver.

Made specifically for repairs done on handheld lawn and garden equipment, this OEM wrench is silver and made of durable metal. It is sold individually. This wrench is sourced directly from the manufacturer and should be replaced once it becomes damaged or worn.

This foam air filter is a genuine Echo replacement part, it is not an aftermarket imitation. It is commonly utilized on backpack blowers. It is designed to remove dust and other contaminants from the air that goes into the engine. One foam filter is included per order. Please note, the plastic filter holder is sold separately. Replacing this item is a very simple task that does not require any tools.

This is an authentic replacement part manufactured for use with Echo backpack blowers, edgers, and trimmers. The screw has multiple applications that vary depending on the model of equipment. This screw is sold individually, please see model diagram for part location and usage.

This genuine replacement fuel cap assembly is sourced directly from original equipment manufacturer for use with Echo backpack blowers. It is designed to keep the fuel in the tank. This assembly includes a retainer that remains in the fuel tank to keep the cap from falling out. It is made from durable plastic and it is sold individually.