This is a light switch for your refrigerator. It activates when the door of your appliance is opened, and it will turn the light inside on and off. You will need to replace this part is if your light is not working properly. In order to make this repair you will need a Phillips screwdriver, a pair of needle nose pliers, and a small flat b...Read morelade screwdriver. This light switch is almost 2 inches long, 1.5 inches wide, and just over an inch thick.
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is an 18 ml, or.6 fluid ounces, bottle of touch-up paint. It also features a brush for easy application. This quick-drying, long-lasting paint...Read more is perfect for fixing any nicks, scratches, or chips on the exterior of your appliance. This paint is white in color, and provides a durable finish.
This ice maker bin temperature sensor is a precision component designed to monitor and regulate the temperature within the ice storage compartment of select refrigerators. By continuously detecting temperature levels, it communicates real-time data to the appliance’s electronic control board, helping to optimize ice production and prevent...Read more issues such as excessive melting or overfilling. Constructed for reliability, this genuine OEM part is compatible with a range of models from Whirlpool, KitchenAid, Maytag, and other affiliated brands. Proper installation ensures consistent ice quality and efficient operation—model verification is recommended prior to purchase.
Appliance spray paint is a great way to cover up any chips and scratches that have appeared on your appliances. Instead of replacing the part entirely, this is an easy fix. This is also a great way to give a fresh new look to any handles or areas that have discoloring due to wear. Make sure to clean the area before you begin and wear a pr...Read moreotective mask for safety. Give the can a good shake and spray a few inches away from the surface. Apply the paint until the area is fully covered as desired. Wait until the paint has dried before using the appliance.
This authentic OEM black touch-up paint is specifically designed for repairing minor scratches, chips, or blemishes on your kitchen appliances. The bottle contains 16ml or 0.6oz of black paint and has an applicator brush under the cap, the same way a nail polish bottle is designed. Restoring these visible damages is important because crac...Read moreked or chipped surfaces can become a breeding ground for dirt and bacteria. If your existing bottle of paint has a thick or clumpy consistency, do not use it. Remember to shake the bottle before applying the paint to your appliance. Please keep in mind that this bottle is sold individually.
This is a condenser fan motor for your refrigerator/freezer. This fan motor is most commonly used with frost-free refrigerators with a condenser coil. It controls the rotation of the condenser fan blade. When the compressor runs, so does this fan, circulating air through the refrigerator grille, cooling the compressor and condenser coils....Read more This fan motor also helps to evaporate excess water in the drain pan. This model is all white in color, and is roughly 4 inches long, 3 inches wide, and 3.5 inches thick.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Warren - For model number KUIX335HPS01
March 31, 2026
The machine makes ice then switches to defrost mode shortly afterwards. I have to turn it off for a few minutes to keep the ice. Eventually it will defrost and start the cycle over. Thoughts?
Hi Warren, thank you for contacting us. We would suggest checking the ice bin thermistor, part number PS11755842. It may be sending incorrect temperature readings to the control board, telling it to start a defrost cycle when one isn’t needed. You may need to replace it to fix the issue. We hope this sorts out your problem!
ice maker goes into harvest cycle too often so it makes thin ice but melts before it makes it to cutting grid
Hi Mitchell, thank you for contacting us. We would suggest checking the ice maker thermistor, part number PS11755842. It is designed to monitor and regulate the temperature within the ice storage compartment. You may need to replace it to fix the issue. We hope this solves your problem!
It said on the filter, which I successfully changed, that you pour 14 gallons of water through the water filter. Does that meant to pour 14 gallons in into the filter that I just put in? Or what else does that mean, If that is true then I remove it and put it back in (immediately)and turn ice maker back on and thats it or do I pour the water some other place which I cant figure out. And do I wait 24 hours before turning it back on? Help!!!!!!!!
Hello Terri, thank you for contacting us. Don't pour any water into the filter, and don't take it back out. "14 gallons" means the amount of water that needs to run through the new filter to flush out the air and carbon dust. Your household water supply does that automatically. Just leave the filter installed, make sure the water valve is open, and turn the ice maker back on. You don't need to wait 24 hours. Since your machine has no water spout, it flushes the filter by making ice. Throw away the first 2 to 3 bins of ice. Early batches may look cloudy or have tiny black flecks, which is harmless carbon dust. After that, the ice is clear and safe to use. Glad to be of assistance!
Was this helpful?
Thank you for voting!
Prev
1
Next
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Door switch module wore out
40 of 55 peoplefound this instruction helpful.
Fred from Oceanport, NJ
Easy
Less than 15 mins
Pliers
Pull out old module... Remove 2 wires... Tape to inside wall [don't want them to fall down into side panel]..
Order new switch..
Fed Ex pkg came on 2nd day..
Install wires on switch... Press into opening... Check door light on..[OK] .. Done
Was this helpful?
Thank you for voting!
Water not refilling after initial batch of ice
19 of 20 peoplefound this instruction helpful.
Jonathan from WILLIAMSBURG, VA
A Bit Difficult
30 - 60 mins
Nutdriver, Screw drivers
The water filled on startup (actually over-filled, which was a clue). After that water was used to make ice, no new water came in so the recirculation pump just made whining noises in the mostly empty reservoir. Since water could come in (on start up) I reasoned it wasn't the water inlet valve, and everything else suggested the ice maker
... Read more was getting inaccurate info about how much water was in the reservoir. Turns out, the water recirculation pump has a water level sensor built in. So while the pump itself still functioned, the water level sensor inside had gone bad. Replacing the pump fixed the issue. There are videos online that show how to accomplish that, but it was pretty straight-forward. The dis-assembly was sometimes irritating because it's hard to see and maneuver around inside. It'll help if you put the machine closer to eye level. Pay close attention to videos that show the disassembly because there are a couple of tabs that are hard to find.
Read less
Was this helpful?
Thank you for voting!
Ice bin overfilling
16 of 21 peoplefound this instruction helpful.
Travis from N CHESTERFLD, VA
Very Easy
Less than 15 mins
Nutdriver
I'm an hvac/r technician, and regularly work on ice machines. Begin my pulling the white over beneath the control panel. It snaps in place so pull on the bottom then left out. 1/4 nut driver is all you need, and remove the screw holding the bin thermistor clip to the side. Up to the right , beneath the control panel, behind the plasti
... Read morec panel you previously removed is the mollex connector. Unplug the thermistor and follow instructions in reverse to reinstall.
My Orders
