Models
>
KUIO18NNXS0
KUIO18NNXS0 KitchenAid Ice Maker - Overview
Sections of the KUIO18NNXS0
[Viewing 6 of 6]
Manuals & Care Guides for KUIO18NNXS0
Click to downloadManual
Owner's Manuals
(1.4MB)
Manual
Owner's Manuals
(4.92MB)
Specs
Product Specifications Sheet
(0.3MB)
Keep searches simple, eg. "belt" or "pump".
Screw, 8/18 x 3/8
PartSelect #: PS11746840
Manufacturer #: WP90767
This screw is sold individually.
$5.42
In Stock
PUMP
PartSelect #: PS16730541
Manufacturer #: W11566405
A recirculating pump is used with standalone ice cube makers. It circulates the water over the top of the evaporator plate, which produces a layer of ice that is then broken down into ice cubes. If yo...
$67.84
In Stock
Screw
PartSelect #: PS11742755
Manufacturer #: WP489483
This screw is sold individually.
$13.09
In Stock
Thermistor
PartSelect #: PS11755741
Manufacturer #: WPW10503764
This is a bin thermostat made for standalone ice makers to activate the ice maker shut-off when bin is full. It senses how much ice is in the bin to determine if it should produce more ice or activate...
$75.62
In Stock
Door Light Switch
PartSelect #: PS11738900
Manufacturer #: WP2149705
The purpose of the light switch in your refrigerator is to automatically turn on the light when the door is opened. If the light does not come on automatically when you open the door, the contacts ins...
$30.34
In Stock
Ice Cutting Grid Wire
PartSelect #: PS370853
Manufacturer #: 4387020
There is approximately 10' of wire. Note: 2 kits are needed to replace both directions.
$60.72
In Stock
Ice Cutter Grid Complete Assembly
PartSelect #: PS11740334
Manufacturer #: WP2313637
If your freestanding ice maker is not producing ice properly, the ice cutter grid assembly may need replacing. The cutter grid is located within the main unit of the ice maker and contains thin, heate...
$272.69
In Stock
Temperature Sensor
PartSelect #: PS11756166
Manufacturer #: WPW10548509
This is a temperature sensor. It may also be known as an ice maker sensor and is used in conjunction with your ice machine. This piece is roughly 3.5 inches long, almost 2.5 inches wide, and includes ...
$91.12
On Order
Drain Fastener Cap
PartSelect #: PS11739077
Manufacturer #: WP2185696
This is a drain fastener cap and is used in conjunction with your freezer/refrigerator. This model is almost 1.5 inches in diameter, half an inch thick, and is white in color. This piece will fasten t...
$20.94
In Stock
PUMP
PartSelect #: PS16730543
Manufacturer #: W11566407
This part is a drain pump for your ice maker. When you flush the reservoir on your ice maker to remove impurities, the drain pump is the part that removes the water from the reservoir. This is an auth...
$67.84
In Stock
Ice Maker Water Distributor Tube
PartSelect #: PS11738017
Manufacturer #: W10863947
The water distributor tube distributes water from the reservoir to the evaporator plate.
$49.70
In Stock
Questions And Answers for KUIO18NNXS0
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Trina
January 28, 2020
The water is overflowing on the ice plate and freezing up on the side. The ice sheet gets too thick and does not slide down on to the cutting grid. I am thinking it is an ice level sensor, but I am not sure. Please advise and if possible. I need the part number and pricing. Thank you so much for your help. Trina
For model number KUIO18NNXS0
Hi Trina,
Thank you for your question. If there is water overflowing in the ice maker, a component in the water inlet valve may have failed and you will need to test it with a multi-meter to see if it is working correctly. If this part checks out fine, you will need to check the sensor. Here is a link to one of our videos on YouTube that you may use as a general reference on how to use a multi-meter to test the parts, https://www.youtube.com/watch?v=bWC44fHn0As. We hope this helps. Thank you and have a great day.
Was this helpful?
Thank you for voting!
- < Prev
- 1
- Next >
Common Symptoms of the KUIO18NNXS0
[Viewing 3 of 3]Light not working
Fixed by
these parts
these parts
Show All
Leaking
Fixed by
these parts
these parts
Show All
Noisy
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Broken light switch
Took all the screws out of the plastic shroud that encloses the switch .There only four that I needed to remove, were the two in front where the switches that go,they go in horizontally and two in the back with large washers on them that hold the back to the top of the box that go in vertically.The switch was a snap ( make that two snaps
... Read more
) the wiring is almost self explanatory. then it gos back to the way you took it off. OH! and don't forget to turn the light bulb all the way back in to the socket , so the light will work after you take the time to install it yourself.I had the water supply line from under the box to the water dispenser in the door and the total bill on that was one hundred thirty seven and a hand full of change.Don't be afraid to do it yourself the savings is enough on one one item to make several months payments on a new one Randy the "Handy Man'
Read less
Parts Used:
-
Randy from Hays, KS
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
77 of 128 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
was not making ice
diagnosed no water flow over evaporator checked voltage into pump then checked pump with ohm meter ordered pump and installed by removing access cover and water holding assembly installed new pump replaced water holding assembly and access cover and returned icemaker to service all is well
Parts Used:
-
Richard from North Wilkesboro, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
48 of 57 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Grid Assembly had a broken wire and would not separate the ice sheets into cubes
I removed the 2 screws on each side of the grid and disconnected the electrical plugs attached to the grid. I slid the broken unit out. I then carefully slid the new unit in making sure not to pinch any of the electrical wires. I replaced the mounting screws, plugged the 3 connectors back into place and turned the ice maker back on. I ha
... Read more
d ice cubes within a couple of hours
Read less
Parts Used:
-
Brad from Bakersfield, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
33 of 37 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!