Quick Question!

Have you ever purchased from PartSelect.com before?

Models > KUIC15NLXS1

KUIC15NLXS1 KitchenAid Ice Maker - Overview

Get Parts and Repair Help for KUIC15NLXS1

If you know the ice maker repair part you need, you can browse the list of all parts on the KUIC15NLXS1, or you can search by name or part description. You can also find your part by where it is located on the KUIC15NLXS1 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your ice maker. We’ve also included any installation videos we have for KUIC15NLXS1 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$15.94

Ice Machine Cleaner - 16oz

This product is used to clean the inside of your ice machine. It is meant to be used on a freestanding machine, not an ice machine found in your refrigerator. This product may be n...

$87.13

Condenser Fan Motor Kit

This condenser fan motor kit includes a motor, fan blade, wire harness, and screws. Used in a refrigerator, the condenser fan motor moves the condenser fan blade to direct and move air across the condenser coil. Please note: The manufacturer has changed the appearance of the product from the original. The kit still functions the same as the original part. It is an OEM factory replacement. Make sure to unplug the refrigerator from the power source and wear gloves to protect your hands. Also, a helpful tip is to store food to prevent deterioration when the power is off.

$62.84

Recirculating Pump - 60Hz

A recirculating pump is used with standalone ice cube makers. It circulates the water over the top of the evaporator plate, which produces a layer of ice that is then broken down i...

$137.02

Ice Cutter Grid Complete Assembly

If your freestanding ice maker is not producing ice properly, the ice cutter grid assembly may need replacing. The cutter grid is located within the main unit of the ice maker, and contains thin, heated wires that slice the ice into cubes that are then deposited in the ice bin. If the cutter grid is broken, ice can back up within the ice maker. This part is sold as a complete assembly and is used with freestanding ice makers. Be sure to wear work gloves to protect your hands when completing this repair. This is an OEM part that sources directly from the manufacturer.

$37.71

Thermostat, Bin

This is a bin thermostat made for standalone ice makers to activate the ice maker shut-off when bin is full. It senses how much ice is in the bin to determine if it should produce ...

$15.59

Switch, Plunger Grid/Light

The purpose of the light switch in your refrigerator is to automatically turn on the light when the door is opened. If the light does not come on automatically when you open the door, the contacts inside the light switch may be burned out, meaning it is time to replace the switch. This package contains both the new light switch and a small plastic spacer. To complete this repair, you will need to remove the control panel section of your refrigerator. The only tools you will require for this repair are a 1/4-inch nut driver and maybe a small flat blade screwdriver. Be sure to disconnect the power source from the refrigerator before completing this repair.

$79.54

Pump, Drain

$50.02

Temperature Sensor

This is a temperature sensor. It may also be known as an ice maker sensor and is used in conjunction with your ice machine. This piece is roughly 3.5 inches long, almost 2.5 inches wide, and includes the necessary wiring connector. You will find this part located in the water pump area of the ice cube maker. The function of this part is to determine the water level within the water reservoir. Once the water level reaches a certain point, the sensor will signal the controls to fill the reservoir.

$33.58

Ice Cutting Grid Wire

There is approximately 10' of wire. Note: 2 kits are needed to replace both directions.

$6.20

Touch-Up Paint - White

This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is an 18 ml, or.6 fluid ounces, bottle of touch-up paint. It also features a brush for easy application. This quick-drying, long-lasting paint is perfect for fixing any nicks, scratches, or chips on the exterior of your appliance. This paint is white in color, and provides a durable finish.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Seven year old condenser fan was making noise when it was running.

  • Customer: Josue from Jacksonville, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 176 of 182 people found this instruction helpful
The process to repair was very simple, I removed the back of the refrigerator to expose the motor area. I then removed three screws that held the condenser motor in place. once it was loose I detactched the electrical harness and removed the old motor. I then placed the new motor in place and secured it with the screws and reattached the new electrical harne... read more

Fridge made noise and the center post was HOT!

  • Customer: David from Jefferson City, MO
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 45 of 47 people found this instruction helpful
We have a side-by-side fridge/freezer and we experienced a hot center post (where doors come together) and the fridge made loud noise. Also, the (old) fan motor would start, but then quit, so our issue was the motor.

For me the repair was very easy, but for an unexperienced person it may prove to be difficult. If you must order a motor/fan, do... read more

Broken light switch

  • Customer: Randy from Hays, KS
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 58 of 97 people found this instruction helpful
Took all the screws out of the plastic shroud that encloses the switch .There only four that I needed to remove, were the two in front where the switches that go,they go in horizontally and two in the back with large washers on them that hold the back to the top of the box that go in vertically.The switch was a snap ( make that two snaps ) the wiring is alm... read more