Models
>
KUDP01ILBL1
KUDP01ILBL1 KitchenAid Dishwasher - Overview
Sections of the KUDP01ILBL1
[Viewing 12 of 12]Manuals & Care Guides for KUDP01ILBL1
Click to downloadKeep searches simple, eg. "belt" or "pump".
Door Balance Link Kit
PartSelect #: PS972325
Manufacturer #: 8194001
This part is a door balance link kit, also sometimes known as door cable or door spring cable kit, that helps support the door as it opens and closes by connecting to the dishwasher door hinges. The k...
$33.12
In Stock
Mounting Bracket
PartSelect #: PS11745496
Manufacturer #: WP8269145
The mounting bracket is sold individually, without screws. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking,...
$10.04
In Stock
Dishwasher Silverware Basket
PartSelect #: PS11746119
Manufacturer #: WP8531233
This silverware basket holds utensils in your dishwasher. If it becomes damaged or goes missing, you can replace it with this part. No disassembly is required to replace this part; simply remove the e...
$53.49
In Stock
Upper Wash Arm Kit
PartSelect #: PS392681
Manufacturer #: 8193504
This part contains the mounting clips and helps distribute water from the top of the dishwasher tub.
$44.70
In Stock
Stationary Wheel and Mount
PartSelect #: PS11745464
Manufacturer #: WP8268785
Sold individually.
$30.32
In Stock
Chopper Assembly
PartSelect #: PS1734917
Manufacturer #: W10083957
This chopper assembly chops up/mince the food particles to prevent from clogging the dishwasher pump.
$34.77
In Stock
Fuse Kit
PartSelect #: PS774514
Manufacturer #: 8193762
When replacing these fuses the wire harness must be replaced as well. It is located in the control panel. The harness is included with this part now.
$35.44
In Stock
Door Handle
PartSelect #: PS11745495
Manufacturer #: WP8269117
NOTE: This part is no longer available in white or biscuit. HANDLE only.
$72.95
In Stock
Door Gasket
PartSelect #: PS12348985
Manufacturer #: W11196317
This is a door seal, but you may also know it as a door gasket and it is a part for your dishwasher. It provides a leak proof seal between the tub and the door of your appliance. You will need to repl...
$94.70
In Stock
Rubber Washer
PartSelect #: PS11743934
Manufacturer #: WP717273
The rubber washer is a part which is specific to dishwashers and should not be substituted by a similar part. It works with the heating element to seal the receptacle opening where the heating element...
$7.76
In Stock
Detergent and Rinse Aid Dispenser
PartSelect #: PS11746408
Manufacturer #: WP8558129
This part releases the detergent and rinse aid into the dishwasher.
$90.08
In Stock
Door Release Spring
PartSelect #: PS11745447
Manufacturer #: WP8268540
This spring is located in the door section. Sold individually.
$5.42
In Stock
Questions And Answers for KUDP01ILBL1
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Aimee
October 12, 2023
I’m looking to replace the lower rack of my dishwasher.
For model number KUDP01ILBL1
Hi Aimee, thank you for reaching out. The lower dish rack for your model is part number PS10057160. We hope this information helps!
Was this helpful?
Thank you for voting!
Related Parts:
Daniel
December 28, 2023
Cannot start D/W. Panel indicator shows "CLEAN". Cannot cancel. Any suggestions???
For model number KUDP01ILBL1
Hello Daniel, thank you for reaching out. The flashing "clean light" indicates, a water temperature, heating problem. Most of the time, it is due to a low water temperature. First, try to reset the control board. Flip the breaker off to the dishwasher for 2 minutes. Then re-apply power. If the issue persists, we would recommend checking the high limit thermostat, part number PS11743423. We hope this solves your problem!
Was this helpful?
Thank you for voting!
Related Parts:
- < Prev
- 1
- Next >
Common Symptoms of the KUDP01ILBL1
[Viewing 10 of 10]Door latch failure
Fixed by
these parts
these parts
Show All
Not cleaning dishes properly
Fixed by
these parts
these parts
Show All
Leaking
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Noisy
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Not draining
Fixed by
these parts
these parts
Show All
Not drying dishes properly
Fixed by
these parts
these parts
Show All
Will not dispense detergent
Fixed by
these parts
these parts
Show All
Will not fill with water
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Replaced Hinge Link
Pulled dishwasher from under counter, attached link to spring, hooked spring back into frame/chassis, threaded link through pulleys, attached other end of link onto door, reinstalled dishwasher under counter. All's well. Note-I purchased an extra link anticipating that the other one will fail. They're cheap enough.
Parts Used:
-
Scott from Fort Lauderdale, FL
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
622 of 661 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Loud grinding noise from water pump
Rather than remove the pump assembly - as an earlier post had done - I pulled the entire dishwasher out and laid it down on the floor. This allowed easy, direct access to the motor (that was the hard, messy part). From this point it was easy. Unplug the wiring, remove the retaining bolt, rotate the motor off the mounting brackets and pull
... Read more
it out. Then put the new one in. That was the easy part (about 15 minutes). The entire job took 2-and-a-half hours, most of which was taken in disconnecting, cleaning up and reconnecting the dishwasher. It's much quieter now.
Read less
Parts Used:
-
Steve from Inver Grove Heights, MN
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
219 of 245 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The old upper wash arm fell off.
I dropped the upper rack to its lowest position.
I pulled the upper water channel down from the spring clip [on the top of the washer] to get access to the hole on the top of the front end of the channel. The front end of the channel only drops an inch or two.
I put the new upper wash arm pivot [larger of the two small pieces] ... Read more through the new upper washer arm from the bottom, placed the assembly up into the hole on the under side of the upper water channel, and snapped in the new keeper [smaller piece] through the hole in the top of the upper washer arm.
Finally, I snapped the upper water channel back into its spring clip. It was not even necessary to remove the racks.
There were no instructions or diagrams with the new parts, so it took me a few minutes to be sure which of the two small parts goes in from the bottom and which goes in from the top. Otherwise, I could have installed the new washer arm in one or two minutes.
I pulled the upper water channel down from the spring clip [on the top of the washer] to get access to the hole on the top of the front end of the channel. The front end of the channel only drops an inch or two.
I put the new upper wash arm pivot [larger of the two small pieces] ... Read more through the new upper washer arm from the bottom, placed the assembly up into the hole on the under side of the upper water channel, and snapped in the new keeper [smaller piece] through the hole in the top of the upper washer arm.
Finally, I snapped the upper water channel back into its spring clip. It was not even necessary to remove the racks.
There were no instructions or diagrams with the new parts, so it took me a few minutes to be sure which of the two small parts goes in from the bottom and which goes in from the top. Otherwise, I could have installed the new washer arm in one or two minutes.
Read less
Parts Used:
-
Donald from Sunnyvale, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
173 of 182 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!