KUDC25CHSS1 KitchenAid Dishwasher - Overview

Diagrams for KUDC25CHSS1

See every part. Know exactly what you need.

Parts for the KUDC25CHSS1

$33.69

Middle Spray Arm Kit

★★★★★

(150)

Part #675808

This middle spray arm kit includes an upper spray arm, a holder or hanger, water supply tube or delivery tube, split ring seal, and a screw. The function of these parts is to spray water to all levels of the dishwasher so the dishes will come out completely clean. This kit has recently been redesigned. It does not include the upper suppor...Read more

Read less

$9.62

Dishwasher Upper Spray Arm Mount

★★★★★

(71)

Part #WP8539324

This upper spray arm mount has been redesigned by the manufacturer, so it not longer requires a clip and screw to be installed. To replace this part, first remove the rack stops from the upper dish rack and pull out the dish rack to work on it. Remove the screw holding the spray arm in place, take off the spray arm and slide out the feedi...Read more

Read less

$25.75

Dishwasher Wash Arm Bearing Ring

★★★★★

(38)

Part #WP9742946

This part will fit between the newer type lower wash arm and the wash arm retainer nut of your dishwasher.

$11.77

Lower Sprayarm Seal

★★★★★

(13)

Part #WP3376846

This dishwasher lower spray arm seal, or under spray arm bearing ring, is designed with the split by the manufacturer. It is not damaged or defective, and is sourced directly from the original manufacturer. This part is approximately 2 inches in diameter, made of plastic, and is white in color. This part is mounted underneath the dishwash...Read more

Read less

$9.62

Dishwasher Wash Arm Retainer Nut

★★★★★

(25)

Part #WP9742945

Use this part to secure the lower spray arm of your dishwasher.

$9.62

Tine row Clip

★★★★★

(15)

Part #WP8268816

This clip attaches the Tine row to the rack. Sold individually.

$7.47

Rubber Washer

Part #WP717273

The rubber washer is a part which is specific to dishwashers and should not be substituted by a similar part. It works with the heating element to seal the receptacle opening where the heating element is attached. The rubber washer is used to prevent water leaking from your dishwasher during its cycle. Before making any repairs to your di...Read more

Read less

$105.35

Drain and Wash Impeller Kit

★★★★★

(21)

Part #675806

This dishwasher drain and wash impeller kit comes with both the drain and wash impeller, gaskets, chopper, and installation screw. This part helps stop your dishwasher from leaking and helps with the proper draining of the dishwasher. If you notice that your dishes are not cleaning, the dishwasher is not draining properly, or is making an...Read more

Read less

$46.34

Lower Door Seal Kit

★★★★★

(17)

Part #4172127

NOTE: This part requires a silicon sealant for installation.

$7.47

Dryer Screw

★★★★★

(2)

Part #WP90767

This screw is sold individually.

$7.47

Washer Hose Clamp

★★★★★

(1)

Part #WP596669

This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This clamp is used to securely attach a hose to another part of your appliance, which helps prevent leaks from those connections. Depending on th...Read more

Read less

$51.61

Water Inlet Valve

★★★★★

(21)

Part #W10844024

This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed. NOTE: As per the manufacture this part has been updated from the original part. It may be a different color, and you may need to order an elbow (# W10685193) for the new designed valve to work.

Questions And Answers for KUDC25CHSS1

Ask our experts a question about this model and we'll get back to you as soon as possible!

Sort by:

Mark - For model number KUDC25CHSS1

August 18, 2021

The diswasher is not following the normal program... when you go to cancel, it goes back to rinse and completes that cycle and goes back to do it again. keypad does not react properly

Hi Mark, Thank you for your question. If the control panel is not responding correctly, there may be an issue with the ribbon cable. Before checking the control panel, unplug the dishwasher from the electrical outlet. Overtime a film can build up on the connections where the cable attaches to the electronic control board and this can prevent it from working correctly. Use a pencil eraser to gently remove the film from the connections. This should resolve the issue. Another method to verify if the control panel is working is to disconnect the ribbon cable from the control at P1. Make sure the other connections to the control panel are still made. Then put the control panel back together and leave the dishwasher door open. Restore power to the dishwasher, wait 5 seconds and then close the door. If the control panel is working correctly then the drain motor will turn on for 2 minutes. If the drain motor does not turn on the control panel will need to be replaced. If the control panel is fine then the electronic control board will need to be replaced. The electronic control board listed for your model, part number 8530929, has been discontinued by Whirlpool and you will need to contact them to see if they have information on a replacement. If they provide you with a replacement part number for it, you may call us back with it and we will verify if we have it available for you. If you have any questions, please let us know.

1 person found this instruction helpful.

Was this helpful?

Alice - For model number KUDC25CHSS1

November 29, 2021

Need possibly a new drain or pump not sure the water is not draining from the dishwasher i need a repairman to come out to my house to fix my KitchenAid dishwasher

Hello Alice, Thank you for your inquiry. If your dishwasher is not draining, we can recommend checking the drain and wash impeller kit, the drain check valve, the drain hose, and the pump and motor assembly. You can check the parts for any visible damage, and test the pump and motor assembly with a multimeter. We are a do it yourself company that sells appliance parts, we apologize but we do not send repairmen to your house. Good luck with your repair.

$49.50

Drain Check Valve with O-Ring

$105.35

Drain and Wash Impeller Kit

$410.79

Pump and Motor Assembly

$68.86

Dishwasher Drain Hose w/Connector Ends

Was this helpful?

Common Symptoms of the KUDC25CHSS1

How this model fails, and the parts that fix it.

Not cleaning dishes properly

Fixed by
these parts

Not drying dishes properly

Will not fill with water

Will not dispense detergent

Videos related to models starting with KUDC25CHSS1

Watch our pros, then fix it yourself.

Replacing the Middle Spray Arm Kit

Replacing the Dishwasher Upper Spray Arm Mount

Replacing the Dishwasher High Limit Thermostat

Replacing the Lower Sprayarm Seal

Replacing the Rubber Washer

Replacing the Dishwasher Wash Arm Bearing Ring

Replacing the Upper Dishrack Track

Replacing the Water Inlet Valve

Repair Tips From Fixers Like You

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Dishes not clean and lower wash arm wobbled.

590 of 610 people found this instruction helpful.

James from Jacksonville, FL
Easy
Less than 15 mins
Pliers

Completely removed lower wash arm and replaced bearing ring and seal.

Other Parts Used:

Dishwasher Wash Arm Bearing Ring

Lower Sprayarm Seal

Was this helpful?

Not Cleaning lightly soiled items.

384 of 394 people found this instruction helpful.

Dennis from Cromwell, CT
Really Easy
Less than 15 mins

Removed spray arm thumb nut. Removed spray arm. replaced worn and broken earings and re-assembled in reverse order. Would have done the repair a lot sooner if I had known that PartsSelect was just a few miles up the highway.

Other Parts Used:

Dishwasher Wash Arm Bearing Ring

Lower Sprayarm Seal

Was this helpful?

Water washing out under front door onto floor

195 of 273 people found this instruction helpful.

Kent from Matthews, NC
Easy
Less than 15 mins
Screw drivers

The plastic parts on this spray arm assembly wear with time and the rotation wobble effect creates a wave action in the pool of water at the bottom of the dishwasher. This waves the water onto the front door and forces a leak outside the unit. Replace the lower arm assembly, washer, bearing and nut. They all wear. Also remember to tigh ... Read more

Read less

Other Parts Used:

Lower Wash Arm Assembly

Dishwasher Wash Arm Bearing Ring

Dishwasher Wash Arm Retainer Nut

Lower Sprayarm Seal

Was this helpful?