KUDC10IXSS4 KitchenAid Dishwasher - Overview
Sections of the KUDC10IXSS4
[Viewing 12 of 12]Manuals & Care Guides for KUDC10IXSS4
Click to downloadInstall
Installation Instructions
(10.94MB)
Install
Installation Instructions
(11.09MB)
Manual
Owner's Manuals
(5.36MB)
Keep searches simple, eg. "belt" or "pump".
Lower Dishrack Wheel
PartSelect #: PS3406971
Manufacturer #: W10195416
This OEM gray Dishwasher Lower Dishrack Wheel Assembly is a plastic kit that allows the rack to slide in and out of the dishwasher easily. If it breaks or becomes damaged. sliding will feel difficult....
$46.00
In Stock
Door Balance Link Kit
PartSelect #: PS972325
Manufacturer #: 8194001
This part is a door balance link kit, also sometimes known as door cable or door spring cable kit, that helps support the door as it opens and closes by connecting to the dishwasher door hinges. The k...
$33.09
In Stock
Rack Stop Clip
PartSelect #: PS11750071
Manufacturer #: WPW10195622
This manufacturer-approved Rack Stop Clip is a gray plastic part which can be installed with a screwdriver. Measuring slightly over an inch in length, it prevents the rack from sliding too far and fal...
$8.10
In Stock
Mounting Bracket
PartSelect #: PS11745496
Manufacturer #: WP8269145
The mounting bracket is sold individually, without screws. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking,...
$10.03
In Stock
Chopper Assembly
PartSelect #: PS1734917
Manufacturer #: W10083957
This is a chopper assembly or drain food chopper, and it is designed for your dishwasher. The chopper chops up/minces the food particles in your dishwasher to prevent them from clogging the pump. You ...
$34.74
In Stock
Drawer Track
PartSelect #: PS11750072
Manufacturer #: WPW10195623
This drawer track or rack slider bar is for use in your dishwasher. It connects to the upper dish rack, and allows the rack top slide in and out. You may need to replace this part if your old rack wil...
$49.53
In Stock
Dishwasher Drain Pump
PartSelect #: PS11753379
Manufacturer #: WPW10348269
This drain pump is used in dishwashers to remove water from the dishwasher tub. If the impeller in the dishwasher is damaged or the motor has been shorted out and will not drain, it is possible the bo...
$72.39
In Stock
Dishwasher Door Seal
PartSelect #: PS12348515
Manufacturer #: W11177741
Door seal seals the gap between the opening to the dishwasher tub and the outer edge of the door.
$67.47
In Stock
Spinner Kit
PartSelect #: PS972316
Manufacturer #: 8193983
This is also called the 3rd-level spinner. This part works like a little spray arm at the top of your dishwasher.
$29.50
In Stock
Dishwasher Upper Rack Roller
PartSelect #: PS11753471
Manufacturer #: WPW10350401
This assembly is the wheel and the mount for your upper dishrack. Sold individually. This is an authentic OEM part for use with Whirlpool, KitchenAid, Kenmore and Jenn-Air Dishwashers. The dishrack wh...
$24.89
In Stock
Rubber Washer
PartSelect #: PS11743934
Manufacturer #: WP717273
The rubber washer is a part which is specific to dishwashers and should not be substituted by a similar part. It works with the heating element to seal the receptacle opening where the heating element...
$7.75
In Stock
Tine Row
PartSelect #: PS10057161
Manufacturer #: W10728160
The tine row on your dishwasher rack divides the rack into columns to keep your kitchen items in place during the washing cycle. If you notice that one or more of the tines on your current tine row is...
$51.04
In Stock
Questions And Answers for KUDC10IXSS4
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Stephen
March 7, 2020
My dishwasher has been stopping mid cycle. It appears to be shorting out. I can turn it back on by switching the fuse panel in the house. Sometimes it works completely and other times it stops in the middle. Which part do I need? Thanks
For model number KUDC10IXSS4
Hello Stephen, Thank you for the question. We suggest testing the Door Latch Switches. They can cause the short that can trip the breaker if they are defective. This can also be caused by a defective Dishwasher Heating Element. You can test the parts with a multi meter to confirm. We hope this helps.
Was this helpful?
Thank you for voting!
Related Parts:
Dave
August 30, 2023
I need the lower rack most of the wheels have come off. Or, do I just need new wheels?
For model number KUDC10IXSS4
Hi Dave, thank you for reaching out. The wheel assembly, part number PS11722152, is available separately from the lower rack. If the wheels have come off, you may need to replace this part. We hope this information is useful!
Was this helpful?
Thank you for voting!
Related Parts:
Caroline
December 29, 2023
How can I remove the filter to clean it
For model number KUDC10IXSS4
Hi Caroline,
Thank you for your question. Here is a link to one of our YouTube videos that you may reference for information on how to remove and install the filter. The dishwasher in the video may not be the same as yours, but it will give you a general idea on how to install the part. We hope this helps!
Was this helpful?
Thank you for voting!
- < Prev
- 1
- Next >
Common Symptoms of the KUDC10IXSS4
[Viewing 10 of 10]Not cleaning dishes properly
Fixed by
these parts
these parts
Show All
Leaking
Fixed by
these parts
these parts
Show All
Door latch failure
Fixed by
these parts
these parts
Show All
Not draining
Fixed by
these parts
these parts
Show All
Noisy
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Not drying dishes properly
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Will not fill with water
Fixed by
these parts
these parts
Show All
Will not dispense detergent
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Replaced Hinge Link
Pulled dishwasher from under counter, attached link to spring, hooked spring back into frame/chassis, threaded link through pulleys, attached other end of link onto door, reinstalled dishwasher under counter. All's well. Note-I purchased an extra link anticipating that the other one will fail. They're cheap enough.
Parts Used:
-
Scott from Fort Lauderdale, FL
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
629 of 671 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dishwasher not draining after wash cycle
Caviat: The actual repair is less than 15 minutes, but I spent a lot of time playing with it before I figured out it was that easy and fast. You don't need to remove the dishwasher from the counter to do this. And it will probably help to look at the new part closely so you can understand where the retainer clip is to press it and release
... Read more
the old pump.
First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done.
First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done.
Read less
Parts Used:
-
Andrew from Alexandria, VA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
481 of 537 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Loud grinding noise from water pump
Rather than remove the pump assembly - as an earlier post had done - I pulled the entire dishwasher out and laid it down on the floor. This allowed easy, direct access to the motor (that was the hard, messy part). From this point it was easy. Unplug the wiring, remove the retaining bolt, rotate the motor off the mounting brackets and pull
... Read more
it out. Then put the new one in. That was the easy part (about 15 minutes). The entire job took 2-and-a-half hours, most of which was taken in disconnecting, cleaning up and reconnecting the dishwasher. It's much quieter now.
Read less
Parts Used:
-
Steve from Inver Grove Heights, MN
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
221 of 249 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!