Quick Question!

Have you ever purchased from PartSelect.com before?

Models > KUDA230YWH1

KUDA230YWH1 KitchenAid Dishwasher - Overview

Get Parts and Repair Help for KUDA230YWH1

If you know the dishwasher repair part you need, you can browse the list of all parts on the KUDA230YWH1, or you can search by name or part description. You can also find your part by where it is located on the KUDA230YWH1 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dishwasher. We’ve also included any installation videos we have for KUDA230YWH1 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Manuals & Care Guides for KUDA230YWH1

Click to download
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$4.89

Single Lower Roller Axle

This is the axle ONLY. Wheel is sold separately.

$2.96

Single Roller Wheel

Sold Individually.

$2.96

Screw

This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this sc...

$44.38

Drain and Wash Impeller Kit

This dishwasher drain and wash impeller kit comes with both the drain and wash impeller, gaskets, chopper, and installation screw. This part helps stop your dishwasher from leaking and helps with the proper draining of the dishwasher. If you notice that your dishes are not cleaning, the dishwasher is not draining properly, or is making any unusually loud sounds or grinding noises, this could indicate the impeller and seal kit have broken down and need to be replaced. You will need a #15 and #20 torx driver, a small flat-blade screwdriver, 1/4-inch nut driver, adjustable wrench, and a small hammer and a sharp chisel.

$20.83

Rubber Water Delivery Tube

This rubber tube carries water from the upper spray arm manifold to the receiver of a dishwasher. This thin walled tube can become brittle over time and crack. If it does, it will ...

$2.96

Screw - 8-18 x 5/8

Sold individually.

$28.41

Drain Check Valve with O-Ring

This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the d...

$5.51

Hose Clamp

The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installation, you will need a flat head screw driver to replace the clamp and a drill to access the screws to remove the front of the washer. Be careful if you do not have specific clamp pliers as the clamp could fly off. Once the front of the washer has been removed, take a quick look for water damage or any obvious signs of where the leak is coming from. If it is not obvious, run water to test.

$14.18

Pump Outlet Seal

$6.20

Touch-Up Paint - White

This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is an 18 ml, or.6 fluid ounces, bottle of touch-up paint. It also features a brush for easy application. This quick-drying, long-lasting paint is perfect for fixing any nicks, scratches, or chips on the exterior of your appliance. This paint is white in color, and provides a durable finish.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

roller axels were broken and wheels missing

  • Customer: Robert from Chlemsford, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 467 of 467 people found this instruction helpful
pulled out the old broken axels and pushen in the new ones and then snapped in the wheels. read more

replace roller axles, wheels and silverware basket

  • Customer: William from Washington, DC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 363 of 365 people found this instruction helpful
...popped out the old in with the new...could not have been easier! read more

Dishwasher Not Draining

  • Customer: Lewis from Portsmouth, NH
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 155 of 199 people found this instruction helpful
Ordered both drain & wash impeller kit and the drain check valve with o-ring. Decided to test the cheaper drain check valve first. Pulled dishwasher out from wall & adjacent cabinetry; removed drain hose from disposer and drained as much water as possible; "jacked" side of dishwasher to gain access to drain hose and drain check valve; used pliers to remove ... read more