KTR27A-BS00 (A2) Kawasaki Trimmer - Overview

The Fuel Tank Grommet is a 1-inch, black, rubber part. It attaches to the fuel tank so you can run your fuel lines through it, and is rated as "Easy" to install by most of our customers. If worn or damaged, it will begin to leak fuel, and must be replaced. Refer to your make, model and diagrams to ensure you're choosing the right part.

The fuel filter clamp, is a silver, individually sold, metal part, used to secure the fuel line to the fuel filter. It attaches to the fuel filter and if broken, typically due to fatigue or damage, it should replaced. Installation is rated as "Easy" and requires Pliers and a Screwdriver. When removing the fuel line to remove the old clamp...Read more, make sure you have a bucket to catch the fuel. Refer to your make, model, and diagram to ensure you're choosing the right part.

This Fuel Line (3x5x182) is a 7.25-inch-long rubber part which is installed inside the fuel tank to the carburetor. It runs from inside of the fuel tank and attaches to the fuel filter inside of the tank. The other end attaches to the carburetor. If damaged, the carburetor will not get enough fuel, and the part must be replaced. Installi...Read moreng this part is rated as "Easy" and can be done with pliers and a screwdriver. Refer to your make, model and diagrams to ensure you're choosing the right part.

The Breather allows air to enter the tank, so no vacuum is created as the fuel level drops, which would prevent the flow of fuel to the carburetor.It seals in the gas emissions and fuel at the same time. It is a metal and rubber part, sold individually, rated as "Easy" to install. If damaged, fuel may start leaking from it, and it must be...Read more replaced. The part is attached inside of the fuel cap. Refer to your make, model and diagrams to ensure you're choosing the right part.

The Fuel Tank Cap and Breather is an assembly made up of black plastic parts. You'll know if you need a new one if fuel is leaking, and this appears to be the source. This can happen due to normal wear, fatigue, and damage. This kit is rated as "Easy" to install and attaches to the fuel tank. Refer to your make, model and diagrams to ensure you're choosing the right part.

This replacement spark plug is specially manufactured for use with Kawasaki engines. It is sourced directly from original equipment manufacturer and it is sold individually. Spark plugs are used to deliver the electric current from an ignition system to an internal combustion engine. Over time spark plugs will get dirty or fouled requirin...Read moreg replacement. You should gap your spark plug according to the owners manual of the outdoor product you have. You would need a spark plug wrench or a socket wrench to replace this spark plug.

This 2-cycle in-tank fuel filter is a component in your lawn equipment that ensures clean fuel reaches the engine by filtering out impurities and debris. It is made of durable metal and high-quality felt and is typically located in the fuel lines. A clogged or cracked filter can cause engine sputtering and idling issues, leading to fuel f...Read morelow problems and potential engine damage. Additionally, impurities in the fuel can damage the engine. To install a new filter, first turn your machine off and allow the engine to cool. Use pliers or a wrench to disconnect the fuel lines. Slide out the old fuel filter, taking care to remove any mounting brackets or holders if necessary. This authentic OEM filter is sold individually.

A cutter reel, also known as a line or trimmer head, is a component that is necessary within the cutting head of a trimmer, since it supplies the trimmer with line/spool. This part is made of plastic and is an OEM part that measures approximately 4.2-inches in diameter and has 2 lanes for spool storage. Since this part is made of plastic,...Read more it can break or crack from a drop impact, or simply over time and exposure to gasoline, oil and heat. If you find that the spool is not coming out properly, or too much spool is being used at once, this part may need replacing. Replacing this part is as simple as opening the trimmer head and accessing where the spool is housed, removing the previous reel, and replacing it with the new one. This part is sold as an individual part without any securing hardware and is compatible with various makes and models of trimmer.

This cutter head assembly, also known as the trimmer head assembly or bump and feed cutting head, is sourced from the original manufacturer, and guaranteed to fit your trimmer. It consists of the cutting head, which is the main body of the assembly that holds the cutting components and connects to the trimmer shaft; the cutter line/cord, ...Read morewhich is a durable nylon string that rotates to cut through materials; a spool, which holds and advances the cutter cord; and a cutting guard, which provides a protective shield or cover that surrounds the cutter cord. The arbor has a diameter of 8mm and left-handed threads with a pitch of 1.25. The head can hold 20 inches of a 0.95-inch diameter cutter line. The cutter head assembly can fail due to mechanical damage to the body, worn-out or tangled strings, or a faulty spool, causing the trimmer to lose its cutting ability. To remove the head assembly, simply twist it off the trimmer shaft. Remove any dirt or debris that may be built up on the shaft and twist the new assembly on the shaft.

This is a genuine OEM sourced replacement recoil starter which is commonly used on Kawasaki lawn and garden equipment. It is the component which allows a user to easily pull-start the unit. It is a complete assembly which includes a plastic housing, starter pulley, starter spring, and the pull rope with a grip, please note the hardware to secure the assembly is sold separately.

This is an authentic manufacturer made replacement part which is specially designed for use with Kawasaki string trimmers. The fuel tank houses the fuel used to power the machine. This part is made of hard plastic and is sold individually. The fuel cap (part number: 51048-2083) is sold separately. For installation, you will need a screwdriver to remove and shrouds and covers.

This is a genuine OEM supplied replacement part that is designed for use with Kawasaki lawn and garden equipment. It is utilized to keep the fuel in the tank. It includes a retainer that remains in the tank to keep the fuel cap from being lost or falling on the ground. One durable plastic fuel cap is included per order.