This EveryDrop Filter3 is certified to reduce the most contaminants with Triple Filtration Technology. Now, you and your family can enjoy the enriching benefits of cleaner, freshly filtered ice & water. Not just in beverages, but for preparing meals, too. This advanced generation of ice and water refrigerator filters from EveryDrop Filter...Read mores are certified to reduce more contaminants with Triple Filtration Technology. Filter 5 reduces 16 contaminants, so you can feel reassured that you and your family are getting the most out of your water. Remember to replace your refrigerator filter every 6 months to maximize contaminant reduction.
Automatic ice harvesting relies on this refrigerator ice maker control module and motor assembly to coordinate the operating cycle. Located behind the ice maker cover, it drives the ejector mechanism and controls the sequence for loosening, releasing, and refilling the ice mold. A failed module may leave cubes stuck in the mold, stop the ...Read moreice maker from cycling, or cause unusual clicking during operation. Water supply problems and incorrect freezer temperatures can cause similar symptoms, so a lack of ice alone does not confirm module failure. This is an OEM part sourced directly from the manufacturer.
If your refrigerator’s interior light is not working, the door switch may be the cause. It turns the light off when the door closes. This is an OEM part. Confirm compatibility using your refrigerator’s model number.
This appliance light bulb illuminates the interior compartment so stored items are easier to see and reach. Its clear glass design allows light to spread through the surrounding area, while the incandescent filament produces light when powered. A burned-out filament or damaged bulb may leave the compartment dark. Replacing a failed bulb h...Read moreelps restore interior lighting. Disconnect appliance power and allow the old bulb to cool before removal, then gently screw the replacement into the socket without overtightening and reinstall the protective cover. This is an OEM part sourced directly from the manufacturer.
When an ice maker is not making ice, its OEM ice level control board kit may be the part to check. The kit’s emitter and receiver use an infrared beam to sense the ice level in the bucket and signal the ice maker to make more.
This refrigerator ice maker fill cup dispenses the water into the ice cube mold during the fill cycle. Replacing the water fill cup is a possible solution if you notice that the ice maker is leaking, or not making/dispensing ice. If you notice the fill cup has been damaged or cracked; replace the part straight away. This water fill cup is...Read more a genuine OEM part and will fit most refrigerators, but check the list of compatible brands to make sure yours is included before purchasing.
A warm refrigerator or noisy evaporator fan can indicate a problem with the fan blade. This white, four-blade OEM part circulates cold air over the refrigerator’s evaporator coils. Confirm fit using your refrigerator’s model number.
This refrigerator ice dispenser drive shaft seal forms a barrier around the shaft beneath the ice bucket. It helps keep moisture and condensation from reaching the auger motor and inner door area. A torn, brittle, or worn seal may allow water to pass through, leading to leaks, rust, or moisture buildup near the dispenser mechanism. Replac...Read moreing a damaged seal helps protect the motor area and restore the barrier around the shaft. Unplug the refrigerator before accessing the drive assembly or removing the shaft. This is an OEM part sourced directly from the manufacturer.
This refrigerator ice level emitter flipper cover helps control the light beam used to monitor the ice supply. The white plastic flap pivots on a spring-loaded hinge beside the ice bucket. Cracks, broken hinge points, or a sticking flap may interfere with the beam and interrupt ice production. Replacing a damaged cover helps restore prope...Read morer flap movement and ice level sensing. Unplug the refrigerator before accessing the assembly, and handle the hinge pin, retaining clip, and spring carefully during replacement. This is an OEM part sourced directly from the manufacturer.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
No ice
567 of 688 peoplefound this instruction helpful.
Daniel from Suwanee, GA
Easy
15 - 30 mins
Screw drivers, Socket set
removed flap door in front of icemaker...removed 3 screws with bolt heads...removed one additional screw with bolt head and ice unit slid out. I removed motor unit (pops out no screws). Replaced and had ice within 3 hours.
Was this helpful?
Thank you for voting!
there were directions
754 of 1282 peoplefound this instruction helpful.
Kate from Jacksonville, FL
Very Difficult
30 - 60 mins
We didn't know where the product went and it was very difficult to install.
Was this helpful?
Thank you for voting!
six months the light turns red. time to replace filter
310 of 392 peoplefound this instruction helpful.
Leroy from Perkiomenville, PA
Really Easy
Less than 15 mins
First I shut the water off to the refrigerator.then i pushed the big button in the middle of the grille below the refrigerator door. pulled out the old filter, took the front cap off the old filter put it on the new filter. took the two red caps off the new filter. pushed the filter in till it locked in place. all done! Turned the back on
... Read more.