This part is a retaining ring, sometimes called a retaining clip, that holds the drum support roller onto the shaft of a dryer. It is made entirely of metal and measures less than an inch in diameter. The retaining ring is a genuine OEM part sourced directly from the manufacturer. The ring may vary in appearance due to manufacturer substi...Read moretution, but the function is the same. You may need to replace this part if the dryer is noisy during tumbling, will not tumble, or takes too long to dry. Be sure to check drum support roller kit and shaft before ordering parts.
This Flat Beater Part Number WPW10672617 is for Stand Mixers. Attaches to the beater shaft and is for normal to heavy mixtures such as cake batters or cookie dough. This has a powder coated finish.
This wire whip is for stand mixers.
Wire whip attaches to the beater shaft and incorporates air into cream, eggs and frostings.
Follow the instructions in the owner's manual for using and installing this part.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Deb - For model number KSM150PSMC0
March 24, 2024
My mixer will not stay in the off position.
Hi Deb, thank you for contacting us. Based on our research, the issue could be with the speed control plate, part number PS11748567. It controls both the speed of the mixer and its on/off function. You may need to replace it to fix the issue. We hope this solves your problem!
My mixer has very little power at low speed, but seems fine at higher speeds. The back part of the main housing is warm to the touch. Could there be something wrong with my motor?
Hi Mike, Thank you for writing. This is normally an indication the Speed Control Plate is faulty and may need to be replaced. We woudl also suggest replacing the Speed Governor with the plate. Thank you for the inquiry, good luck with the repair!
What would make the mixer only function in speed #1, all other speeds do nothing. There were no funny sounds or smells, such as burning.
Hi Gary,
Thank you for your question. If you are unable to adjust the speed to a higher setting then you will need to replace the speed control plate. If the mixer was stuck on the highest setting, then you would need to replace the phase control board. The part number listed under your model number for the speed control plate is PS11748567. If you would like to place an order for it, you may order it either online or by calling our customer service line and anyone will be happy to assist you. We hope this helps! If you have any questions, please let us know.
mixer is having a incorrect speed control. always run at high.
Hello Ian, thank you for asking. We would recommend checking the speed control plate assembly, part number PS11748567, to fix the issue. We hope this helps!
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Speed Control Lever KNOB BROKEN
163 of 209 peoplefound this instruction helpful.
Robert from Minot, ND
Easy
Less than 15 mins
Pliers
Pulled the Knob off of the new Lever then pressed it on the old Lever. I had to order the whole lever because it was the part nearest the knob in the illustrated parts break-down. I RECOMMEND THAT THE KNOB BE ADDED TO THE ILLUSTRATED PARTS BREAK-DOWN.
Was this helpful?
Thank you for voting!
motor would run but mixer wouldn't operate: broken worm gear
88 of 94 peoplefound this instruction helpful.
Raymond from Shirley, MA
Easy
30 - 60 mins
Screw drivers
My girlfriends' stand mixer failed when the accessory drive cap fell into the mixing bowl and jambed the beater, spliting the worm gear. The teeth on this gear are made of nylon and are molded to an aluminum center. This part is designed to fail in situations like this, saving the more expensive transmission parts. Following a repair manu
... Read moreal I found online, I first removed the rear cover and pulled out the cord strain relief out from the base. Next I removed the drip cup from around the base of the planetary drive. I then used a pin punch to drive out the pin holding the planetary to the center shaft and removed the planetary. The unit was then inverted and I removed 4 screws holding the bottom cover to the gear case, and the 5 screws from around the planetary drive. The bottom cover was then lifted off. Three screws holding the worm gear bracket in place were then removed and the worm gear assembly lifted out. A small pin holds the worm gear to the shaft. I drove this out with a small pin punch and the shaft and worm gear were then removed. There is also a thrust washer on this shaft, and it's location is important. Make a note for re-assembly. The new gear was installed and the entire process reversed for re-assembly. A successful repair completed! My girlfriend would have replaced this $200 appliance, but I was able to repair it for less than $30 including shipping.
Read less
Was this helpful?
Thank you for voting!
Mixer was making clunking sounds and shaking
90 of 109 peoplefound this instruction helpful.
Robert from Minden, NV
Easy
1- 2 hours
Screw drivers
I removed screws in a sequence that I felt wouldn't further damage the mixer until I had it completely unassembled. When I found the broken worm gear, I went online to find a part. I found an exploded view, but the part numbering was old, and the salesperson couldn't tell me what the worm gear and bracket assembly consisted of, as I only
... Read morewanted the worm gear. After trying to drive the pin out of the assembly, and failing, I decided to back online and see if anyone else had a photo of the assembly. Luckily (and wisely) PartSelect,com did and that answered any questions I had. The price was better, too. Reassembly of the mixer was a cinch with the exploded view. It's working like new, and we're hoping for another 35 years of service from it! Thanks.
My Orders
