Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This EveryDrop Filter3 is certified to reduce the most contaminants with Triple Filtration Technology. Now, you and your family can enjoy the enriching benefits of cleaner, freshly filtered ice & wate...
The lower door closing cam is used in refrigerator doors, it can be located on the fresh food side or the freezer side. It helps hold the door open. This cam is made out of plastic, so it might crack ...
This Ice Maker (Icemaker Assembly, Complete Icemaker Assembly, Ice Maker Assembly, Refrigerator Ice Maker) can be used with 25-27 cubic feet refrigerators that have a vertical auger dispenser located ...
The “Icemaker Control Assembly” (Module & Motor Assembly, Ice Maker Control Module, Icemaker Module, Refrigerator Ice Maker Module) is what controls the actions of your ice maker. The control turns th...
This is a refrigerator ice guide that is made entirely of clear plastic. This ice guide is located in the freezer door. Turn your refrigerator ice dispenser off before replacing the part. This is a si...
If you have ice building up in your freezer, or if your freezer is getting too warm during the defrost cycle you may need to replace the bi-metal defrost thermostat. The function of the defrost bi-met...
This light bulb is a 120 volt, 25 watt incandescent appliance light bulb with a small base screw-in that fits in a variety of appliances such as microwaves, refrigerators, freezers, cooktops, or stove...
In this kit you will find the support, the ice door, spring, and delay. The heater ribbon is no longer needed and therefore will not be included with this part. This kit works in the dispenser chute t...
This set of two electronic control boards includes both the emitter and receiver modules, which work together to manage ice production and dispensing in compatible refrigerator models. The emitter sen...
Ask our experts a question about this model and we'll get back to you as soon as possible!
4 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
RAY
November 10, 2022
evaporator fan goes off and on continually freezer and reefer holding temp for now
For model number KSCS23INSS01
Hello Ray, thank you for contacting us. We would recommend checking the thermistor, part number PS11739132. Sometimes due to a shorted thermistor, the control board senses the wrong temperature and it turns the fan on and off repeatedly. If this does not help, the evaporator fan motor, part number PS11723174, is probably faulty. Customer service is available 7 days a week if you need help placing an order. Glad to be of assistance!
fan shuts on and off refridgerator and freezer holding temperature then locks out unplugged and reset unit comes back to correct temperature then it starts short cycling fan again
For model number KSCS23INSS01
Hi Ray,
Thank you for your question. In models that use an electronic control board, a thermistor or temperature sensor may be used to monitor fresh food and freezer temperatures. The sensor is a small capsule like device that is protected by a plastic shield and will vary in resistance depending on the temperature. The control board uses this information to turn on the compressor and fan circuits as well as to operate the damper control on some models. If a sensor becomes damaged or defective it may incorrectly signal the control board to turn off the compressor and fans and result in warmer than normal fresh food and freezer temperatures. You will need to test the thermistor for continuity with a multimeter to see if it is working correctly. The thermistor will need to be placed in ice water for 5 minutes to bring it to 32 degrees F before testing it. Set the multimeter to the Rx1 setting and place the probes on the terminals. You should receive a reading of 16600 ohms (+/- 5 percent). If you receive a reading outside this range, you will need a replacement temperature sensor or thermistor. We hope this helps with the repair!
Need replacement for light bulb on the ceiling of this refrigerator. Tried many standard appliance 40W 120V bulbs, none work.. Help, what do I need?
For model number KSCS23INSS01
Hello Sue, thank you for reaching out. We would recommend using the model compatible parts only. The light bulb that you are referring to is part number PS11747806, and it is 120V 25W. Glad to be of assistance!
removed flap door in front of icemaker...removed 3 screws with bolt heads...removed one additional screw with bolt head and ice unit slid out. I removed motor unit (pops out no screws). Replaced and had ice within 3 hours.
Remove the icemaker service door... gently pry the door pins from the hinge sockets. Remove the 3 screws from the under side of the icemaker with a nut driver (1/4"). Gently remove the icemaker . It's a tight fit between the top of the compartment and the icemaker lower support tray. Next, disconnect the electrical connector at the ri
... Read moreght side. You're done! Reverse procedure for installing. Good luck. Remember, your working with cold plastic...take your time and don't force too much.
