KRB750A (A1) Kawasaki Leaf Blower / Vacuum - Overview

The Fuel Tank Grommet is a 1-inch, black, rubber part. It attaches to the fuel tank so you can run your fuel lines through it, and is rated as "Easy" to install by most of our customers. If worn or damaged, it will begin to leak fuel, and must be replaced. Refer to your make, model and diagrams to ensure you're choosing the right part.

The fuel filter clamp, is a silver, individually sold, metal part, used to secure the fuel line to the fuel filter. It attaches to the fuel filter and if broken, typically due to fatigue or damage, it should replaced. Installation is rated as "Easy" and requires Pliers and a Screwdriver. When removing the fuel line to remove the old clamp...Read more, make sure you have a bucket to catch the fuel. Refer to your make, model, and diagram to ensure you're choosing the right part.

The Breather allows air to enter the tank, so no vacuum is created as the fuel level drops, which would prevent the flow of fuel to the carburetor.It seals in the gas emissions and fuel at the same time. It is a metal and rubber part, sold individually, rated as "Easy" to install. If damaged, fuel may start leaking from it, and it must be...Read more replaced. The part is attached inside of the fuel cap. Refer to your make, model and diagrams to ensure you're choosing the right part.

The Fuel Tank Cap and Breather is an assembly made up of black plastic parts. You'll know if you need a new one if fuel is leaking, and this appears to be the source. This can happen due to normal wear, fatigue, and damage. This kit is rated as "Easy" to install and attaches to the fuel tank. Refer to your make, model and diagrams to ensure you're choosing the right part.

This is an OEM part sourced directly from the manufacturer. The carburetor priming pump is found in Kawasaki backpack leaf blowers and small engines. This part is made of high-quality plastic, and is used to inject priming fuel into the carburetor. This item is provided as an individual replacement part.

This is a genuine OEM supplied replacement part that is designed for use with Kawasaki lawn and garden equipment. It is utilized to keep the fuel in the tank. It includes a retainer that remains in the tank to keep the fuel cap from being lost or falling on the ground. One durable plastic fuel cap is included per order.

This is an authentic replacement part sourced directly from the manufacturer. The shoulder band is found in Kawasaki backpack leaf blowers. This part is made of fabric, and is used to provide comfortable shoulder straps to allow the user to wear the machine as a backpack. You may require a wrench or screwdriver when replacing this item. The shoulder band is available as an individual replacement part.

A Stopper is a black plastic part used to attach the pad to the frame. Refer to your make, model, and diagrams to ensure this is the right part for you. It is sold individually, is rated as "easy to install", and requires a hammer for installation. If broken it must be replaced.

This is an authentic item that is supplied by the original equipment manufacturer for use with Kawasaki engines commonly installed on lawn and garden equipment. It is one of the special diaphragms that ensure an air-tight seal in the carburetor, please make sure to refer the appropriate diagrams of your model for the correct location and ...Read moreapplication of this hardware. Unfortunately, over time gaskets and diaphragms tend to wear out and may begin to fail eventually requiring a replacement. Keep in mind this high-quality component is made of durable composite material and is sold individually.

The Recoil Assembly, also known as the recoil starter, is used to engage the flywheel when the rope is pulled, in order to turn the engine over so that it wil start. If broken, it may not engage the flywheel (which will be noticeable when you pull the rope. The rope may even break). If broken, the part must be replaced. Installation is ra...Read moreted as "Easy" and requires a wrench, socket set, and screwdriver. It attaches on top of the engine where the flywheel is. The assembly is black in color. Refer to your make, model and diagrams to ensure this is the correct part.

The Frame Pad is a 10 x 11.5-inch part used to reduce vibrations from the motor. A damaged Frame Pad won't reduce vibrations very well, and should be replaced. The pad is rated as "Easy" to install and can be attached onto the frame. Refer to your make, model and diagrams to ensure this is the right part for you.