KP0800 (Type 2) Makita Planer Jointer - Overview

Length 8 Foot Length: 6' Gauge: 18 Wires: 2 Type: Bare Wire This power supply cord is a genuine OEM sourced replacement part. It is specially made to supply power from a standard outlet to Makita power tools. A cracked or damaged cord should be replaced before continuing to use the tool. This rubber insulated cord is sold individ...Read moreually. It comes with a rubber sleeve grommet that is not sold separately. Replacing this power supply cord you will need a screwdriver. • Remove the housing screws • Remove the the housing • Disconnect the old cord wires • Remove the old power cord • Secure the new cord in place • Connect the wires • Reassemble and test the new cord

This is a genuine OEM sourced replacement part designed for use with Makita planers. It helps to hold and secure the planer blade to the unit. It is made out of metal and it is sold individually. You would need a wrench to replace this item.

This tapping screw is an authentic hardware that is supplied by original tool manufacturer for use with a variety of Makita power tools. It has multiple uses depending on the model of your unit, please make sure to check appropriate diagrams for correct location and use of this screw. Note this durable metal screw is sold individually.

This #191938-1 (CB-408) Makita carbon brush set contains two individual carbon brushes with wire leads and brush springs attached. The set contains genuine Makita replacement parts, and comes packaged in a Makita retail box. This brush set will fit the Makita tools listed at the bottom of the page. • Worn brushes are often the cause...Read more of a poorly running motor • Replacing brushes can fix an intermittent motor • New brushes can restore a motor's electric braking Carbon motor brushes are one of the most commonly replaced power tool components. Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power. A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned. When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.

This cord guard is a genuine Makita replacement part, and it is a direct replacement for a damaged or missing cord guard. Power tool cords undergo a lot of stress, and these cord guards help to alleviate some of that stress at the weakest point--right where the cord enters the tool. Over time cord guards will deteriorate and eventually re...Read morequire replacement. Keeping a strong cord guard on your tool will help will cord life. This cord guard is compatible with the tools listed below, but it is not guaranteed to fit any other power tools.

This authentic replacement part which is specially designed for use with Makita power tools. Ball bearings are used to reduce friction between rotating parts, over time components may begin to wear out and fail eventually requiring a replacement. Please note this high-quality ball bearing is made of durable metal and it is sold individually.

Included in Part Number 516306-1. rnThis Ball Bearing is sealed on both sides. This genuine Makita replacement part is sold individually. rnrn • Ball bearings minimize friction between rotating parts in your tool. The balls or rollers bear the load and spin, distributing the weight evenly, while the minimal contact area of the balls re...Read moreduces friction. This reduces wear on the tool, allowing it to run smoothly. rn • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

This is genuine OEM sourced replacement parts designed for use with Makita planers. These are double-edged tungsten-carbide planer blades that are 3-1/4"long. Planer knives are machined to make very precise cuts. When knife blades wear down, you won't get the level of precision you require and the blades would need to be replaced. These a...Read morere double edged blades for double the cutting life. To replace the blades you will need a wrench.

Genuine Makita replacement part, this part is sold individually. This screw is used to secure various internal and external parts in the tool models shown below.It is a metric screw sized M4 X 16 (W, SW).

This set contains two drum plates that are genuine OEM parts sourced directly from the manufacturer. They attach to the set plates and the drum and are used in Makita planers. They are made out of metal and will need to be replaced if they become broken. A wrench and a screwdriver may be needed during the replacement of these parts.

This manufacturer sourced replacement pin is made out rubber and it is sold individually. It acts as a cushion/spacer in a variety of Makita power tools. This is a standard piece of hardware and it has multiple applications based on your tool. Please refer to diagrams for correct application.