This a genuine OEM microwave cooking tray. It is also known as a microwave turntable or microwave plate. The function of the tray is to hold and rotate food items while the appliance is in use to ensure the food is being heated evenly. This cooking tray is made of transparent glass, and may need to be replaced if the tray is cracked or br...Read moreoken. A broken tray may prevent it from rotating if the three partial circles on the bottom of the tray will not connect to the turntable driver. This part is sold individually and is approximately 12 inches in diameter. It is recommended to check the drive coupling, or turntable driver, if tray is not turning.
If the microwave exhaust fan is not circulating air properly, there could be an issue with the grease filter. A dirty filter will cause your microwave to run less efficiently and can alter the taste or smell of your food. Filters should be changed every six months for maximum performance. These silver, aluminum filters are sold separately...Read more, and are approximately 13 3/8 inches long x 5 7/8 inches wide. Measure your current filter to assure correct replacement. Check your grease filters regularly for particles and grease buildup to see if cleaning is necessary. If there is any visible damage to the filter, it should be replaced straight away.
This is a package of 2 filters. The charcoal filter is used in microwaves to remove food odors from the air. If your filter is damaged or strong odors are coming from your microwave, it is best to replace this part. The only tool needed for this repair is a Phillips screwdriver. First, remove screws at the top of microwave to access the f...Read moreilter. Next, remove filter and insert new filter by pushing it all the way back, so the edges hit the two tabs. The front edge of the filter should rest at the bottom of the cavity. Make sure to replace the grill after installing the new filter. Remember to unplug your microwave from the power source before the installation process. This part is metallic and measures about 12 inches wide and 6 inches deep.
This turntable ring in your microwave makes sure that your glass tray rotates smoothly. Located just above the internal floor, it supports the tray so that your food cooks evenly. A broken turntable ring will look warped or cracked. Additionally, the rotation may become uneven or wobbly. You should replace the ring when it is damaged, by ...Read moresimply taking out the old one from your appliance. Please note that this replacement part is sold individually and is a genuine OEM product, specifically designed for your microwave.
This surface light bulb is used in ranges and microwaves. It has a high voltage of 12 and 10 watts. This bulb illuminates and directs light at the bottom of the microwave or the inside of it. It also illuminates the top and bottom of an oven. If your bulb breaks, or the light flicks on an off, replacing it will solve your issues. Pro tip:...Read more High voltage capacitors in ranges and microwaves can retain lethal electrical change even when unplugged, to ensure your safety a technician should install this part. Refer to the manual provided by the manufacturer for further instructions.
This diode, or high voltage diode, is used in microwaves. It is an electrical current control device that ensures power flows in one direction and not the other way. If your microwave produces no heat, heats inconsistently, or gets noisy, replacing this part can be the solution. The tools needed for this replacement are a nutdriver, plier...Read mores, and screwdrivers. First remove the microwave cover, then remove the old part by disconnecting the small thermostat. Replace with the new diode. Remember to use the diagram provided by the manufacturer for more instructions.
If your microwave is not turning on it could be due to your fuse needing to be replaced. This part protects the microwave by shutting it off if there is an electrical surge. This fuse is just over an inch long, is metallic on both ends and ceramic in the middle. Before beginning this repair, unplug the appliance and wait a few minutes bef...Read moreore starting. Remove the outer cabinet which is held in place with two screws. You will then locate the power cord which will lead you to the fuse holder. Determine if the fuse has blown. Using an ohmmeter, you should be able to figure out if it has blown. A proper reading is zero ohms, if it reads as anything else then your fuse has in fact blown. Simply snap the old fuse out of place and place the new one in.
This is an authentic manufactured drive coupling for a microwave. It fits on the motor shaft to hold and rotate the glass turntable tray while the appliance is running. This part has a D-shaped insert for the motor shaft, and measures approximately 3 inches in diameter. You may need to replace this part if the microwave tray will not turn...Read more. No tools are required for this repair. It is recommended to check the support ring before ordering the drive coupling in case the wheels are broken. This part is also known as a turntable coupling or microwave turntable support.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dirty Grease Filter
953 of 968 peoplefound this instruction helpful.
Joseph from Las Vegas, NV
Really Easy
Less than 15 mins
Slide grease filter about 1/2 inch to right (or left) using the d-ring attached to one side and then pull down and out. Push charcoal filter frame slightly to rear and pry down from front. Install new charcoal and grease filters by reversing process. No tools - 5-minutes max!!
First -- and this was the key to success -- I watched a couple of Youtube videos on "Replacing a microwave door handle". As one video suggested, I placed a large towel underneath where I was working (over the stovetop) to catch any falling parts but this proved unnecessary. Once I removed the two screws from the end of the door, the ins
... Read moreide of the door pried off easily with a screwdriver. It did want to drop quickly though, so be ready to hang onto it. The handle was attached with two screws (which I reused, no problem). It took a few minutes to re-insert the inside of the door into the frame, but once that's done, you just re-install the two end screws and you're finished.
Read less
Was this helpful?
Thank you for voting!
broken glass turntable
403 of 420 peoplefound this instruction helpful.
Deborah from Baltimore, MD
Really Easy
Less than 15 mins
No repair- just replaced glass turntable. Right part I needed with first try