Quick Question!

Have you ever purchased from PartSelect.com before?

Models > KGYE960WWH0

KGYE960WWH0 KitchenAid Dryer - Overview

Get Parts and Repair Help for KGYE960WWH0

If you know the dryer repair part you need, you can browse the list of all parts on the KGYE960WWH0, or you can search by name or part description. You can also find your part by where it is located on the KGYE960WWH0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for KGYE960WWH0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$8.98

Thermal Fuse

This thermal fuse is designed for use in dryers. It is a safety mechanism that stops the flow of electricity to the heating element when a dryer overheats. When this fuse is faulty...

Order within the next 11 hrs and your part ships today!
$14.56

Multi Rib Belt - 92-1/4"

This multi rib belt is an important part in your dryer, it is what helps rotate the drum. The belt attaches to the drum, idler pulley, and motor pulley. As the armature of the motor rotates, the belt begins to move and turns the drum. If you notice the drum of your dryer is not spinning during the dry cycle, but you hear the motor running, your belt may have snapped and it will need to be replaced. This belt features four ribs and three grooves, however it replaces a wide variety of belts including wider styles that had five ribs and four grooves. When installing this part make sure the grooves are facing down, against the drum. This replacement part is 92 1/4 inches in length, and 1/4 inch wide. Before you begin any repair work, make sure your dryer has been unplugged.

Order within the next 11 hrs and your part ships today!
$3.56

Door Catch Kit

This is a door catch kit, and it is designed for use with your dryer. On your appliance you will find both a strike and a catch, these two parts work together to keep your dryer do...

Order within the next 11 hrs and your part ships today!
$21.73

'M' Series New Style Coil Kit

This is an M series new style coil kit, used in gas dryers. When the igniter reaches a high enough temperature, these coils work together to let the gas enter the dryer. The coils open the gas valve; if the valve does not open the heating element will not ignite. Both coils must be operational for the valve to open. This is a safety mechanism to ensure that there are no unsafe buildups of gas inside your appliance. This kit comes with a three-terminal boost/hold coil, and a two-terminal main coil. Each part is approximately 1 1/4 inches in diameter. If the igniter glows but shuts off without igniting gas, it means one of both of your valves is faulty. We recommend you replace these as a set. Before you begin this repair unplug your appliance and shut off the gas supply.

Order within the next 11 hrs and your part ships today!
$3.80

Light Bulb - 40W

This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these repla...

Order within the next 11 hrs and your part ships today!
$10.34

Drum Support Roller

This is a drum support roller for a dryer. The part includes the drum roller only and does not include the tri rings. Although most dryers require two drum support rollers, this part is sold separately. It is recommended to check and replace both drum support rollers at the same time to ensure proper drum rotation and because they often wear at the same rate. The drum support roller holds the drum in the proper position while it spins on the support wheels. If rollers are worn out, they will cause the dryer to be noisy. This is a genuine replacement part.

Order within the next 11 hrs and your part ships today!
$17.97

Igniter Kit

If your dryer will not heat, takes too long to dry, or does not provide enough heat, you might want to replace your igniter kit. This silicone carbide igniter with ceramic holder k...

Order within the next 11 hrs and your part ships today!
$10.04

Idler Pulley Assembly

This part provides the tension required for a multi-ribbed belt. It also serves to help the belt to rotate the drum and attaches to the idler pulley wheel. If your dryer will not start or tumble, takes too long to dry, or is noisy during operation, you may need to replace the idler pulley assembly. Make sure to disconnect power before installing this part, and work gloves are recommended to protect your hands. While the dryer is disassembled for this repair, consider replacing the drive belt as well. You will need a putty knife, a Phillips screwdriver and a 5/16 nut driver for this repair.

Order within the next 11 hrs and your part ships today!
$21.40

Thermostat, Internal-Bias

Part may differ in appearance, but functions the same as original part. This part controls the temperature of the inside of the dryer drum and prevents the dryer from overheating.

Order within the next 11 hrs and your part ships today!
$5.76

Tri Ring

If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pulley shaft, or on the rear drum roller shaft. In either case, you will need to remove the front panel of the dryer and the drum to access the part for repair. Once you have accessed the damaged tri ring, you will simply need to slip it off and replace it with the new one. This part is sold individually. Be sure to disconnect the power source from the dryer before you begin this repair.

Order within the next 11 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer was working, but no heat.

  • Customer: ANTHONY from CHESHIRE, CT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 2147 of 2415 people found this instruction helpful
First I unplugged the dryer, then removed the back panel, this exposed most all of the wiring and I could see the heater coils.
Not knowing what the problem was I started looking at the coils and could not see any broken parts.
So then checked the thermal fuse for continuity I removed the two wires from it with a small pair of needle nose pliers, ... read more

Dryer tub belt broke

  • Customer: Ray from Denton, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 858 of 911 people found this instruction helpful
Removed the two screws that attatch the lent channel to the top of the dryer, then lifted the top of the dryer by pushing in on the two locking tabs located at the front , left and right , corners of the dryer top with a small flat head screw driver. The top of the dryer will fold back out of the way. At this point I removed the two 1/4 inch screws that are ... read more

No heat but would run otherwise

  • Customer: Dana from Grassvally, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 668 of 700 people found this instruction helpful
Cleaning the lint out of the whole machine took quite a bit of time--it was everywhere. Underneath the lint trap was a collection that ultimately ruined the thermal fuse where it restricted the air flow considerably.

Ascertaining the problem was the most time consuming part.

The actual repair was quite simple and didn't take but 15-20 m... read more