This oven rack is chrome in color and is approximately 24.76 inches wide by 15.78 inches deep. If your old oven rack is damaged, you should consider replacing it. Many of our customers have determined this repair to be very easy. You will not require any tools to complete it. To replace the oven rack, simply pull the old rack out, and rep...Read morelace it with the new one. Make sure to put the new rack back in the oven with the beveled edge in first. To keep your oven racks clean, we recommend that you pull them out before using the self-cleaning function on your oven.
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch. It has 6 threads. Refer to the manual provided by the manufacturer for further information on repair and accurate guidance. Remember to wear work gloves as a safety precaution.
The temperature sensor measures the temperature inside the oven. If your oven is too hot, not heating evenly, is not heating enough when baking, or simply will not start, you could have a faulty temperature sensor. A faulty temperature sensor can be a fire risk. If your sensor is not working properly, you should look to replace it straigh...Read moret away. A failed oven sensor is most often responsible for F3 or F4 error messages on electronically-controlled ovens. Make sure you disconnect the power to your range before you start your repair.
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is an 18 ml, or.6 fluid ounces, bottle of touch-up paint. It also features a brush for easy application. This quick-drying, long-lasting paint...Read more is perfect for fixing any nicks, scratches, or chips on the exterior of your appliance. This paint is white in color, and provides a durable finish.
This thermostat is also known as a thermal cut-off fuse and is used in conjunction with your range. This part establishes and maintains the internal temperature of the oven cavity. When the temperature of your range gets too hot it will trip the high-limit thermostat safety, this will cut the power to the oven so that it does not continue...Read more to overheat. For this installation, you will need a Phillips screwdriver and a pair of needle-nose pliers. If your oven does not heat after a self-cleaning cycle you may need to replace the high-limit thermostat.
This part is a light bulb that is 120-130 volts and 15 watts, and is used in conjunction with your range or wall oven. The function of this bulb is to illuminate the interior of the oven.Before making this repair, you will need to disconnect your appliance from the electrical source. We recommend wearing work gloves to protect your hands ...Read moreduring this installation. No tools will be required for you to make this repair. However, if your old bulb breaks while you are trying to remove it, you will need a pair of pliers to grasp the socket and twist it until it comes out.
This part is the replacement door gasket for your oven. It is now made of black rubber and is sold individually. The door gasket runs along the circumference of the oven door and creates a seal that insulates the oven and keeps heat in. If your oven will not heat up properly, or if you notice that the door gasket has become loose or worn,...Read more it may need to be replaced. To replace the door gasket, you will need to remove the retaining bracket at the bottom of the oven door, then carefully pull the gasket away from the front of the oven cavity. Then, push the new gasket inside the groove on the outside of the oven cavity, securing it with the arrowhead fasteners that are built in to the oven cavity. This is an OEM part from the manufacturer.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
JACK WHITE - For model number KGSS907SSS03
November 30, 2019
I have one repair man he said it is probably the transformer so I put a new 1 in the stove wpw10111628 / when I plugged the 110 in their was sparks for 1 second at the plug i also noticed the bored went on the front of the stove went crazy. I guess new part I put in is not happy I thank you for trying to help me jack white
Hi Jack, not sure what happened, I would make sure you received the right part by checking the part number on the transformer. Its possible its another part is causing the issue, like the control board might be faulty. Thank you for your question and good luck with your repair!
My cook top burner igniters do not now work. What do I do? Should the igniter control need replacing? I do not see it in any of the diagrams.
Hello Richard, thank you for your question! According to our research on your model, make sure the Spark Module, part number PS11753037, is working fine with a multimeter and the electrodes or wire connections are not loose. If it does not help, the issue is probably related to the Surface Ignitor, part number PS11747388. The surface burner igniter produces the spark that lights the surface burner. We hope this helps.
Hi-I need the gas igniter module—I’m only getting a slight tick under the main pan—I have not taken all the screws out to disassemble-unless I have the part ? Any suggestions
Hi Robert, thank you for reaching out. The spark module for your model is part number PS11753037. We would suggest replacing it to fix the issue. We hope this solves your problem!
Hydro was working on the power lines.There was some kind of power surge the stove will not work anymore
Hi Jack, one of the electronic components likely went out. You would need a multimeter to test them. You would be most likely looking at the control board or thermostat. Thank you for your question and good luck with your repair!
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Self Cleaning blows the thermostat fuse
137 of 157 peoplefound this instruction helpful.
Joseph from Worthington, PA
Really Easy
15 - 30 mins
Screw drivers
Something Kitchen Aid wont tell you but running a self clean on this model stove blows the fuse located on the back of the stove.
First I slid the stove out and removed the back of the stove held in place by 8 Phillips screws. The thermostat fuse is located near the top middle on the back of the stove. Remove the 2 screws hold
... Read moreing it in place. Disconnect the wires, plug in the new part. Put it all back together. Job done in less than 30 minutes.
This repair would have cost $164 through A&E factory service.
Read less
Was this helpful?
Thank you for voting!
Power shut down and door lock-up after self-cleaning
52 of 58 peoplefound this instruction helpful.
john from new market, MD
Really Easy
15 - 30 mins
Screw drivers
My wife used the self cleaning function for the first time after 1.5 years of owning, of course out of warranty. A quick google search identified the problem. Called Kitchenaid, they said of course it can't be that simple, they had never heard of this problem, need to schedule a service call. Googled and found this site, Ordered the part
... Read more, came in, only took a screwdriver and about 20 minutes, just like all the other posts.
shame on Kitchenaid for not owning up to the problem. I even e-mailed them all the links, they did not acknowledge them.
Read less
Was this helpful?
Thank you for voting!
oven and broiler not working
34 of 46 peoplefound this instruction helpful.
Pamela from chicago, IL
Really Easy
Less than 15 mins
Screw drivers, Wrench (Adjustable)
I just looked at the tech sheet on the range and tested the gas valve with an ohm meter to see how much resistance I had and compared it to the tech sheet and noticed the gas valve was bad. So I replaced it with a new one from part select which arrived very fast. It was quite easy to replaced it.
My Orders
