EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

KF19 - Overview

Models starting with KF19

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Door Mullion Spring – Part Number: DA81-01345B
$9.85
On Order
Door Mullion Spring
★★★★★
★★★★★
(69)
Part #DA81-01345B
Keep the center door flap moving smoothly with this replacement spring for select French door refrigerators. The spring adds tension so the flap opens and closes as the doors move. Replace it if the flap stays open, blocks the door, or makes a rattling sound. Unplug the refrigerator before starting the repair. Check the exact appliance model number before ordering.
Spring PIN - French – Part Number: DA81-01346A
$6.40
In Stock
Spring PIN - French
★★★★★
★★★★★
(20)
Part #DA81-01346A
When the folding divider on a French-door refrigerator will not retract, the spring pin or sleeve may be worn or broken. This support piece helps hold the mullion spring in the left door so the flap moves as the doors open and close. Check for a missing spring, cracked hinge point, bent flap, or door alignment problem before choosing a replacement. Confirm fit with the full appliance model because small sleeves can differ. Record the spring position before removal and avoid forcing brittle plastic. Install the sleeve in the same direction shown in the service diagram, reconnect the spring carefully, and test the flap before loading the door with food.
Hinge – Part Number: DA61-03230B
$7.65
On Order
Hinge
★★★★★
★★★★★
(5)
Part #DA61-03230B
This is a French door hinge that is compatible with various models of refrigerators and is used to control the mullion (long plastic strips) on the inside portion of the French doors. If you notice that your doors open and the mullion either moves freely or is stuck, this hinge needs to be replaced immediately to prevent issues with frost buildup, energy efficiency and temperature fluctuations. Replacing this hinge is quite simple, and you will only need a flathead and Philips-head screwdriver to do it. First, remove the screw covers from the securing screws for the mullion. Unscrew and remove the securing screws with your Philips-head screwdriver, and then pull the mullion up and out carefully to dislodge it from the fridge door. Near the middle of the mullion, disconnect the wire harness to remove the mullion completely. Remove the hinge cover with a flathead screwdriver to expose the hinge, and then carefully remove and replace the old hinge onto its attaching spring. Then you can simply reassemble the rest of the door assembly, along with the hinge cover and wire harness.
Refrigerator Door Gasket - White – Part Number: DA63-07733A
$90.43
On Order
Refrigerator Door Gasket - White
★★★★★
★★★★★
(4)
Part #DA63-07733A
This is a door gasket, also known as a door seal, for Samsung refrigerators. This door gasket is used to create a barrier between the cooled interior temperature of the refrigerator, and the warmer temperature of your home. If this door gasket is warped or damaged in any way, you need to replace it immediately so your fridge can continue to cool optimally. To replace this gasket on your fridge, you simply need to pull off the old gasket, and carefully wrap this new one around the perimeter of the door. This gasket is sold individually and does not come with any other parts or accessories.
Bi-Metal Defrost Thermostat – Part Number: DA47-00243K
$53.27
In Stock
Bi-Metal Defrost Thermostat
Part #DA47-00243K
If ice is building up in your freezer or if your freezer is getting too warm on the defrost cycle you may need to replace the bi-metal thermostat.
Evaporator Fan Motor – Part Number: DA31-00146H
$142.24
In Stock
Evaporator Fan Motor
★★★★★
★★★★★
(3)
Part #DA31-00146H
This evaporator fan motor is sourced from the original manufacturer for use in refrigerators. It circulates cold air throughout the refrigerator compartment to maintain consistent cooling. If the evaporator fan motor is faulty, you will notice inconsistent internal temperatures, excessive and unusual noise, and frost build up. To begin the repair, disconnect the refrigerator from power and remove all shelves and food items in front of the rear panel. Remove the mounting screws on the rear panel and carefully detach it to expose the fan motor. Disconnect the wire connectors to the motor and pull it out of the refrigerator. You may reuse the old fan blades if they are in good condition. Insert the new motor in the refrigerator and reattach the mounting screws. Reconnect the wire connector and reassemble the refrigerator in reverse order.
Case Cap – Part Number: DA67-01650A
$9.85
In Stock
Tapping Screw – Part Number: 6002-000213
$6.40
In Stock
Tapping Screw
Part #6002-000213
Fan Blade Assembly – Part Number: DA31-00010D
$29.74
In Stock
Fan Blade Assembly
★★★★★
★★★★★
(1)
Part #DA31-00010D
This condenser fan blade (part number DA31-00010D) is for refrigerators. Condenser fan blade DA31-00010D moves air across the condenser coil to cool the hot refrigerant before it enters the evaporator. Safely store any food that could deteriorate while the power is off and unplug the refrigerator before installing this part.
Door Support with Mullion Heater - White – Part Number: DA97-07661C
$170.09
In Stock
Door Support with Mullion Heater - White
Part #DA97-07661C
This white-colored flipper or mullion assembly serves as a seal mechanism found between the French doors of your refrigerator. It measures 36 inches in length and 2 inches in width. Positioned along the inner edge of one door, it flips into place to close the gap when the doors meet. A broken assembly might result in loose door closure and escaping cold air, so it is important to replace it to keep your food fresh. This genuine OEM replacement part is sold individually.
Refrigerator Roller – Part Number: DA61-04703A
$12.05
In Stock
COVER-HEATER FRENCH – Part Number: DA63-03454B
$16.45
In Stock
COVER-HEATER FRENCH
Part #DA63-03454B
COVER-HEATER FRENCH;AW-P

Common Symptoms of models starting with KF19

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Left side French Door flap on Samsung refrigerator didn't retract when closing.
51 of 70 people found this instruction helpful.
  • HOLLIE from FORT WAYNE, IN
  • Very Easy
  • Less than 15 mins
OMG seriously! I stopped into my go-to appliance repair shop to ask about what might be needed to repair the problem with my refrigerator door. They said you will need to replace the Mullion Flap piece. Cost would be $250-300 with part, labor and service. I went on line to see if I could handle the repair process myself. I found a How to - U Tube video and turns out I only needed to replace a little spring and pin not the whole Mullion Flap. Went to Parts select, ordered the spring and pin and did the repair myself in about 5 minutes. Shipping was $7 so I ended up paying $13 total.
Was this helpful?
Thank you for voting!
Installation Video Incorrect
34 of 44 people found this instruction helpful.
  • Cheryl from PALATINE, IL
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers
The installation video notes that the door mullion spring has a bent end, and that the bent end of the spring is to be inserted into the LOWER hinge. However, on my refrigerator door, the bent end of the door mullion spring must be inserted into the UPPER hinge in order for the door to function properly. (Also noted that in your video t he installer manually closed the door mullion rather than just closing the refrigerator door, another indication that the installation of the spring was incorrect.) After watching the video several times to confirm I was installing the door mullion spring according to the video instructions, I tried inserting the bent end of the door mullion spring into the upper hinge, which proved to be the correct installation of the door mull spring. What should have been a 5 minute repair turned into an ½ hour repair.
Was this helpful?
Thank you for voting!
Broken Mullion Door spring-mullion remains open and must be manually folded in
14 of 21 people found this instruction helpful.
  • Bruce from BEND, OR
  • Really Easy
  • Less than 15 mins
  • Pliers
Placed new spring pin and new spring in place with pliers-10 seconds tops. HOWEVER!! Your instruction video is INCORRECT. Spring must be placed opposite of video with bent side toward million otherwise million is flipped outward not held closed. Two frustrating days before I figured that out.
Was this helpful?
Thank you for voting!