This OEM gray Dishwasher Lower Dishrack Wheel Assembly is a plastic kit that allows the rack to slide in and out of the dishwasher easily. If it breaks or becomes damaged. sliding will feel difficult....
$46.04
In Stock
Order within the next 10 hrs and your part ships today!
This part is a door balance link kit, also sometimes known as door cable or door spring cable kit, that helps support the door as it opens and closes by connecting to the dishwasher door hinges. The k...
$33.12
In Stock
Order within the next 10 hrs and your part ships today!
This OEM Dishwasher Upper Rack Adjuster is a grayish-black, plastic part which will require a screwdriver to install. It fits onto the dishwasher rack and connects it to the track allowing it to slid...
$43.85
In Stock
Order within the next 10 hrs and your part ships today!
The mounting bracket is sold individually, without screws. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking,...
$10.04
In Stock
Order within the next 10 hrs and your part ships today!
The tine pivot clip, also known as the tine row pivot, is used in dishwashers and is located in the upper dishrack. At around 3 inches in length, the clip is used to keep the tine row in place in the ...
$10.68
In Stock
Order within the next 10 hrs and your part ships today!
Also known as rack adjuster. Sold individually.
This is an original part from KitchenAid, Kenmore, Whirlpool, Jenn-Air, and Maytag for use with Dishwashers. The dishrack adjuster arm positioner clip...
$38.25
In Stock
Order within the next 10 hrs and your part ships today!
This is the dishrack slide track for the left side of various dishwashers. This track allows your upper dishrack to be supported and slide in and out of the dishwasher to place or remove dishes from t...
$84.26
In Stock
Order within the next 10 hrs and your part ships today!
Sold individually.
This dishrack adjuster is for dishwashers.
Dishrack adjuster lets you change the height of the dishwasher's upper rack.
Wear work gloves to protect your hands when installing this part.
$46.08
In Stock
Order within the next 10 hrs and your part ships today!
This dish rack slide rail is a genuine OEM replacement part that is compatible with various models of dishwasher. It is designed to fit on the right side of the dishwasher. The slide rail or track sup...
$71.80
In Stock
Order within the next 10 hrs and your part ships today!
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
$11.80
In Stock
Order within the next 10 hrs and your part ships today!
This water inlet valve should be located behind the lower kick plate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.
$64.02
In Stock
Order within the next 10 hrs and your part ships today!
Questions And Answers for KDTE334GPS0
Ask our experts a question about this model and we'll get back to you as soon as possible!
8 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Ed
October 25, 2022
upper dish rack attaching parts to slide. need part # for left side
For model number KDTE334GPS0
Hello Ed, thank you for reaching out. The dish rack slide track for the left side that you have requested is part number PS12584376. If you need help placing an order for it, please feel free to give us a call. We look forward to hearing from you!
UNIT SEEMS TO HAVE LOST POWER. NO LIGHTS. ACTS LIKE A FUSE ISSUE. CAN YOU CHANGE THE FUSE IN THIS MODEL?
For model number KDTE334GPS0
Hi Marcus, thank you for the question. First, make sure your dishwasher is getting power, if it is getting power then check the following parts to fix your problem: door latch, part number PS1175696, and control panel, part number PS12348000. Please reach out to customer service if you need help placing an order, anyone will be happy to assist you. We hope that helps.
Hi, the black hinge rests on a metal pin with flat head, allowing the door to pivot and rest on. One side of my dishwasher door pin is broken. Under what parts I should look for.
Thanks for your help in advance.
For model number KDTE334GPS0
Hi Raffi, thank you for reaching out. The metal pin you are looking for does not come separately. It comes as a part of the door hinge. The door hinge for the right side of your model is part number PS11746183, and the door hinge for the left side is part number PS16875381. You may need to replace the faulty one to resolve this issue. We hope that helps!
LEAKING WATER AT BOTTOM THROUGH OUT THE CYCLE DRIPPING AT WHITE VALVE/SOLOIND AREA THANKS FOR ANY HELP
For model number KDTE334GPS0
Hello Ken, thank you for reaching out. According to our research on the model, the problem appears to be with the Door Seal, part number PS12348515. If that does not help then the issue is likely to be with the Seal, part number PS11731683. Customer service is always available to help you place an order if you are having trouble doing so. Good luck with your repair!
Can I replace the door hinges, they have been sprung.
For model number KDTE334GPS0
Hello Terrie, Thank you for your inquiry. Researching the model number that you have provided, we show the door springs as part# PS11745526, the mounts as part# PS11748211 and the door balance kit as PS972325. We hope this helps you.
Pulled dishwasher from under counter, attached link to spring, hooked spring back into frame/chassis, threaded link through pulleys, attached other end of link onto door, reinstalled dishwasher under counter. All's well. Note-I purchased an extra link anticipating that the other one will fail. They're cheap enough.
1. Open the dishwasher and remove the two plastic grommets about halfway down on either side of the opening. Then remove the two screws under the grommets.
2. Remove the kick plate under the door. May have to lower unit by turning the feet using the adjustable wrench.
3. Make sure you have enough slack in the water i
... Read morenput line and electrical wiring that you can pull the dishwasher out about 12 inches or more.
4. There is a spring and nylon rope link on both sides of the unit. Probably just one link is broken, but the replacement comes with two, so you can replace both or save one as a spare. Look at the good side and it should be pretty self explanatory how it attaches. I found it easiest to first thread the link around the lower pulley, then attach the link to the spring, then spring to the rear support, then the link to the door.
This was the second time I had this problem so I knew the symptoms and remedy. The tools needed were two nut drivers a ¼” and 5/16” along with a flat pry bar and Phillips screw driver. I started by removing the lower front panel by removing the two ¼” screws on either side. The lower panel will lift up and then can be removed by pullin
... Read moreg on the bottom. There is a flat sheet metal piece behind the front panel with insulation that can be removed very easily along with the front panel. When the front panel is removed it exposes the front legs that may need to be dropped to let you lift the dishwasher over the tile (if you have ceramic tiles). The next step would be to remove any ties to the counter top if it is attached. Mine were attached by the two straps on either side with Phillips screws. After the top is free, lower the front legs by lifting the dishwasher with the flat pry bar and threading the legs up into their holders. With the legs lifted the dishwasher can be pulled out to expose the tension springs located along the sides at the very bottom. Chances are the ropes are broken off the plastic holders that fit over the door hooks. Remove the plastic guides by removing the 5/16” nut from the middle of the lower roller. Remember to note which hole the screw is coming from this also sets the tension for how fast or slowly the door drops. Placing the nut closer to the front will drop the door slowly and toward the back will drop the door more quickly. I placed mine in the middle hole. When the plastic guides are removed attach the nylon pope to the spring and attach to the back of the dishwasher. There is a hole located on a flat piece of sheet metal the spring will attach to at the back of the dishwasher (if it is broken). Check the other side if it is still in tact. With the spring in place weave the rope around the plastic guides then pull the springs to help get the plastic end over the door hook located at the bottom of the door. Repeat this operation for the other side (kit has a both sides covered) and reinstall dishwasher in cabinet. Steps 1) Remove front panel (1/4” nut) 2) Release Dishwasher from Cabinet 3) Lower front legs 4) Pull Dishwasher out from under Cabinet 5) Remove Rope Guide (5/16” nut) 6) Install new Rope Guide (Supplied in Kit) 7) Attach new rope to Spring and attach spring to dishwasher 8) Weave rope through rope guide 9) With door closed pull spring to relieve tension so rope can be attached to door 10) Repeat for other side (Kit has both sides)