KBL35A-AS00 (KBL350A - A1) Kawasaki Trimmer - Overview

The Fuel Tank Grommet is a 1-inch, black, rubber part. It attaches to the fuel tank so you can run your fuel lines through it, and is rated as "Easy" to install by most of our customers. If worn or damaged, it will begin to leak fuel, and must be replaced. Refer to your make, model and diagrams to ensure you're choosing the right part.

The Primer, or priming pump, is a plastic part that attaches to the carburetor. It's rated as "Easy" to install by most of our customers. This part is used to pump fuel from the fuel tank to the carburetor or to start the engine. If damaged, it will no longer pump fuel. It may also be physically, noticably broken. Replace this part if dam...Read moreaged. Check your make, model and diagrams to ensure you're choosing the right part.

The fuel filter clamp, is a silver, individually sold, metal part, used to secure the fuel line to the fuel filter. It attaches to the fuel filter and if broken, typically due to fatigue or damage, it should replaced. Installation is rated as "Easy" and requires Pliers and a Screwdriver. When removing the fuel line to remove the old clamp...Read more, make sure you have a bucket to catch the fuel. Refer to your make, model, and diagram to ensure you're choosing the right part.

This Fuel Line (3x5x182) is a 7.25-inch-long rubber part which is installed inside the fuel tank to the carburetor. It runs from inside of the fuel tank and attaches to the fuel filter inside of the tank. The other end attaches to the carburetor. If damaged, the carburetor will not get enough fuel, and the part must be replaced. Installi...Read moreng this part is rated as "Easy" and can be done with pliers and a screwdriver. Refer to your make, model and diagrams to ensure you're choosing the right part.

The Breather allows air to enter the tank, so no vacuum is created as the fuel level drops, which would prevent the flow of fuel to the carburetor.It seals in the gas emissions and fuel at the same time. It is a metal and rubber part, sold individually, rated as "Easy" to install. If damaged, fuel may start leaking from it, and it must be...Read more replaced. The part is attached inside of the fuel cap. Refer to your make, model and diagrams to ensure you're choosing the right part.

The Fuel Tank Cap and Breather is an assembly made up of black plastic parts. You'll know if you need a new one if fuel is leaking, and this appears to be the source. This can happen due to normal wear, fatigue, and damage. This kit is rated as "Easy" to install and attaches to the fuel tank. Refer to your make, model and diagrams to ensure you're choosing the right part.

This 2-cycle in-tank fuel filter is a component in your lawn equipment that ensures clean fuel reaches the engine by filtering out impurities and debris. It is made of durable metal and high-quality felt and is typically located in the fuel lines. A clogged or cracked filter can cause engine sputtering and idling issues, leading to fuel f...Read morelow problems and potential engine damage. Additionally, impurities in the fuel can damage the engine. To install a new filter, first turn your machine off and allow the engine to cool. Use pliers or a wrench to disconnect the fuel lines. Slide out the old fuel filter, taking care to remove any mounting brackets or holders if necessary. This authentic OEM filter is sold individually.

A cutter reel, also known as a line or trimmer head, is a component that is necessary within the cutting head of a trimmer, since it supplies the trimmer with line/spool. This part is made of plastic and is an OEM part that measures approximately 4.2-inches in diameter and has 2 lanes for spool storage. Since this part is made of plastic,...Read more it can break or crack from a drop impact, or simply over time and exposure to gasoline, oil and heat. If you find that the spool is not coming out properly, or too much spool is being used at once, this part may need replacing. Replacing this part is as simple as opening the trimmer head and accessing where the spool is housed, removing the previous reel, and replacing it with the new one. This part is sold as an individual part without any securing hardware and is compatible with various makes and models of trimmer.

This is a genuine OEM supplied replacement part that is designed for use with Kawasaki lawn and garden equipment. It is utilized to keep the fuel in the tank. It includes a retainer that remains in the tank to keep the fuel cap from being lost or falling on the ground. One durable plastic fuel cap is included per order.

This is an authentic item that is supplied by the original equipment manufacturer for use with Kawasaki engines commonly installed on lawn and garden equipment. It is one of the special diaphragms that ensure an air-tight seal in the carburetor, please make sure to refer the appropriate diagrams of your model for the correct location and ...Read moreapplication of this hardware. Unfortunately, over time gaskets and diaphragms tend to wear out and may begin to fail eventually requiring a replacement. Keep in mind this high-quality component is made of durable composite material and is sold individually.

This is a genuine OEM sourced replacement part that is specially designed for use with Kawasaki lawn and garden equipment. It is a standard hardware that has multiple applications depending on your model, make sure to check appropriate diagrams for correct location and use of this hardware. This part is made from durable metal and it is sold individually.

This is an OEM sourced part that has been manufactured for use with Kawasaki outdoor power equipment with two stroke engines. The gasket is part of the carburetor assembly and is used to seal the connection between the diaphragm and the body of the carburetor. This gasket is available as an individual replacement part.