K33 Karcher Pressure Washer - Overview

This cylinder head plug, also referred to as an outer valve plug, is a genuine OEM replacement part used in pressure washers. It is a plastic cap with one O-ring and locking tabs around the body for added security. It is used to seal the cylinder head to maintain the correct pressure levels, and to prevent water from escaping. Over time i...Read moret is common for the plug to become brittle and break, or the locking tabs may wear down. If the plug is faulty it will need to be replaced to avoid leaking and uncontrolled spraying during operation. To remove the plug, twist it until the locking tabs disengage and pull it out. You may need to use a pair of pliers or a wrench to pry the plug out if there is a buildup of debris around the mounting hole. Each plug is sold individually.

This is a manufacturer sourced replacement part designed for use with Karcher pressure washers. This ring provides an air-tight seal for the cylinder head. Over time this ring will shrink, become brittle and crack allowing for air leaks. At that time it should be replaced. It is made out of rubber and it is sold individually. Replacing this item you would need hex key/allen wrench and pliers to replace this item.

The plug connects to the cylinder head and is made out of plastic. This is a genuine Karcher replacement part used in compatible pressure washers. This item is available as an individual replacement part. A screwdriver and a socket set may be needed to replace the plug if it becomes broken.

This is an authentic OEM part made by Karcher for use in pressure washers. The connection fits next to the filter and the cover on one side and the hose coupling on the other. It is made of plastic and will need replacing if it breaks. A screwdriver might be needed during the installation process. This part is available as an individual replacement.

This authentic OEM sourced part is made for use with Karcher pressure washer. It is one of the special valves for the pump. If it is damaged or is missing, this will provide an identical replacement for the original component that was installed on a new equipment. Please refer to the appropriate diagrams for your model to ensure the exact...Read more location and the correct installation. One durable plastic valve with a spring and an O-ring is included. A wrench set will be needed to take the pump apart to perform this repair.

O-rings are flexible circles which are used to prevent leaks and maintain pressure. This part is an authentic OEM replacement ring used in Karcher pressure washers. These O-rings are used at the connection point between the machine and its hose. This set includes five (5) identical O-rings. Please note that the wand itself uses a separat...Read moree set of O-rings, part # 2.640-729.0 O-Ring Seal Set. Multiple other sizes of O-ring are used in various other spots on these machines; see manual for part numbers and placements.

This grooved ring seal is an authentic OEM replacement part used in pressure washers. It is a rubber seal with a diameter of 0.8 inches. The ring seal is found in the motor housing, where it helps to maintain the correct pressure preventing the water from leaking out of the pump housing. It also prevents water from entering the housing an...Read mored causing damage. Over time the seal may wear down, tear, or fall off leading to leakages and potential contamination. Inspect all the seals in your equipment as they tend to wear down at the same time and replace those that are no longer functioning well. Begin the repair by switching off the equipment. Remove the motor/pump housing and locate the faulty seal. Gently pry it off the cylinder head and discard it. Clean the mounting surface and press the new ring seal into the grooves until it is firmly in place. Reattach the housing to complete the repair. Each grooved ring seal is sold separately.

This is a genuine item that is specially designed for use with Karcher pressure washers. It is supplied by the original equipment manufacturer. The oil helps to lubricate internal components of the pump to ensure it runs properly. Check the oil level regularly. Oil level should always be between the "FULL" and "ADD" level marks on the dip...Read morestick. Be sure the machine is level when checking the oil level. This will prevent them from wearing out. Refer to the owners manual of your model for the correct application of this oil. This synthetic 15W40 oil is sold in a single 1-liter container.

This authentic OEM sourced replacement part that is designed for use with Karcher pressure washers. The purpose of this switch is to control on/off function of the unit. Because switches use mechanical internals, over time they will begin to deteriorate and fail eventually requiring replacement. This durable plastic switch is sold individually.

This is a genuine OEM sourced replacement part designed for use with Karcher pressure washers. This high pressure hose is made out of rubber/plastic material. It is 25 ft long and it is sold individually. This hose can be used on pumps that produce up to 3600 PSI. Easily connects to the washers with M22 connection.

This replacement filter is supplied directly from the original equipment manufacturer for use with Karcher pressure washers. It helps to ensure the water that goes through the unit is free of dirt and other harmful contaminants. It can over time get clogged, damaged or lost eventually requiring a replacement. Keep in mind this high-qualit...Read morey filter is sold as an individual item. Refer to the owner's manual for your model to ensure the correct repair procedure.

This is a genuine OEM supplied part which is specially designed for use with Karcher pressure washers. The filter helps to remove dust and other contaminants from the water that goes through the pump. Over time it may wear out, get damaged or lost eventually requiring a replacement. To ensure the correct application, refer to the owners m...Read moreanual for your model. Keep in mind this high-quality filter is sold as an individual item.