K293PLUS (K 2.93 PLUS 1.601-103.0) Karcher Pressure Washer - Overview

This is a manufacturer sourced replacement part designed for use with Karcher pressure washers. This ring provides an air-tight seal for the cylinder head. Over time this ring will shrink, become brittle and crack allowing for air leaks. At that time it should be replaced. It is made out of rubber and it is sold individually. Replacing this item you would need hex key/allen wrench and pliers to replace this item.

This O-ring is a genuine part from original manufacturer. It is used with the cylinder head in Karcher pressure washers. An O-ring is a flexible circle which acts as a seal between rigid parts. It is a simple component but it is often essential for a machine to function correctly. Sold individually. Note that this ring is available with part # 9.001-104.0 Spare Parts Set.

O-rings are flexible circles which are used to prevent leaks and maintain pressure. This part is an authentic OEM replacement ring used in Karcher pressure washers. These O-rings are used at the connection point between the machine and its hose. This set includes five (5) identical O-rings. Please note that the wand itself uses a separat...Read moree set of O-rings, part # 2.640-729.0 O-Ring Seal Set. Multiple other sizes of O-ring are used in various other spots on these machines; see manual for part numbers and placements.

This grooved ring seal is an authentic OEM replacement part used in pressure washers. It is a rubber seal with a diameter of 0.8 inches. The ring seal is found in the motor housing, where it helps to maintain the correct pressure preventing the water from leaking out of the pump housing. It also prevents water from entering the housing an...Read mored causing damage. Over time the seal may wear down, tear, or fall off leading to leakages and potential contamination. Inspect all the seals in your equipment as they tend to wear down at the same time and replace those that are no longer functioning well. Begin the repair by switching off the equipment. Remove the motor/pump housing and locate the faulty seal. Gently pry it off the cylinder head and discard it. Clean the mounting surface and press the new ring seal into the grooves until it is firmly in place. Reattach the housing to complete the repair. Each grooved ring seal is sold separately.

It is a genuine item that is supplied by the original equipment manufacturer for Karcher pressure washers. This is an identical replacement for a faulty or a missing metal fork that was installed on a new unit. To ensure the exact location and the correct replacement procedure, refer to the appropriate diagrams for your model. Note, this ...Read morehigh-quality fork is made of durable metal and is sold as an individual item. A screwdriver, a wrench set, and pliers might be needed to perform this repair.

This manufacturer sourced replacement part designed for use with Karcher pressure washers. It is the essential part of the unit allowing to direct and control the spray. Please note the wand is sold separately. This pistol assembly is made out of plastic and it is sold individually.

This genuine manufacturer-approved part is specially designed for use with Karcher pressure washers. The spring helps to apply tension to the cage. It is an identical replacement for a missing or a faulty component that was installed on a new unit. Please make sure to refer to the appropriate diagrams of your model for the correct locatio...Read moren and application of this hardware. Keep in mind this high-quality spring is made of durable metal and is sold individually.

It is an identical replacement for a damaged or a missing valve that was installed on a new unit. Check the diagrams for your model to ensure the exact location and the correct application of this part. One durable valve and a metal spring are included. This authentic component is supplied by the original equipment manufacturer for use with Karcher pressure washers.

A genuine item that is supplied by the original manufacturer for use with Karcher pressure washers. It is an identical replacement for a missing or damaged detergent nozzle that was originally installed on a new unit, for the correct location and application of this component make sure to refer to the appropriate diagrams of your model. O...Read morever time the material may wear out and begin to fail eventually requiring a replacement. Keep in mind this high-quality component is made of durable plastic and is sold individually.

This is a genuine Karcher replacement part sourced directly from the manufacturer. The pressure spring is commonly found in Karcher pressure washers. This is a metal part used in the pistol nozzle to maintain tension between the parts, allowing adjustment of the pressure. No tools are required to replace this item. Simply remove the old part and slip the new one into its place. This item is sold individually.