K140 Karcher Pressure Washer - Overview

This O-ring is a genuine part from original manufacturer. It is used with the cylinder head in Karcher pressure washers. An O-ring is a flexible circle which acts as a seal between rigid parts. It is a simple component but it is often essential for a machine to function correctly. Sold individually. Note that this ring is available with part # 9.001-104.0 Spare Parts Set.

This high quality wheel and tire assembly is a genuine manufacturer sourced replacement part that is specially produced for Karcher pressure washers. It is the wheel that supports and helps to move your unit around. This part consists of a durable metal wheel with a rubber tire and it is sold individually, please note the hardware to secure it is sold separately.

This genuine Karcher replacement part is sourced directly from the original manufacturer and is designed for use with compatible pressure washers. The plastic cap attaches securely to the pump housing and serves as a cover for the oil fill spout, helping to protect the internal components from dirt and debris. Durable and easy to install,...Read more this cap is available as an individual replacement part and is ideal for maintaining the performance and longevity of your pressure washer.

This is a genuine Karcher part sourced directly from the manufacturer for use in pressure washers. The seal goes between the washer and the bush. It seals the connection so that water does not leak out. This part is made of hard rubber and is sold individually.

This grooved ring seal is an authentic OEM replacement part used in pressure washers. It is a rubber seal with a diameter of 0.8 inches. The ring seal is found in the motor housing, where it helps to maintain the correct pressure preventing the water from leaking out of the pump housing. It also prevents water from entering the housing an...Read mored causing damage. Over time the seal may wear down, tear, or fall off leading to leakages and potential contamination. Inspect all the seals in your equipment as they tend to wear down at the same time and replace those that are no longer functioning well. Begin the repair by switching off the equipment. Remove the motor/pump housing and locate the faulty seal. Gently pry it off the cylinder head and discard it. Clean the mounting surface and press the new ring seal into the grooves until it is firmly in place. Reattach the housing to complete the repair. Each grooved ring seal is sold separately.

This is a genuine item that is specially designed for use with Karcher pressure washers. It is supplied by the original equipment manufacturer. The oil helps to lubricate internal components of the pump to ensure it runs properly. Check the oil level regularly. Oil level should always be between the "FULL" and "ADD" level marks on the dip...Read morestick. Be sure the machine is level when checking the oil level. This will prevent them from wearing out. Refer to the owners manual of your model for the correct application of this oil. This synthetic 15W40 oil is sold in a single 1-liter container.

This gasket is made of flexible rubber material and fills the space between the bush and the washer. It is used in Karcher pressure washers, and will need replacing if it breaks apart. This gasket is an OEM replacement part and is available as a single item.

This item is sourced from the original equipment manufacturer. It is specially designed for use with Karcher pressure washers. This is one of the special components that are utilized to provide a tight seal for the pump components. Over time it may wear out or get damaged causing water leaks and eventually requiring a replacement. Note, t...Read morehis high-quality grooved ring is made of a durable material and is sold individually. Make sure to check the diagrams of your specific model for the exact location and the correct application. You will need a wrench set to take the pump apart in order to perform this repair.

Genuine Karcher replacement part, this item is sold individually. This is the Water Outlet Connection that the Hose for the Spray Gun attaches to. It is connected to the Pressure Washer by use of the 9.039-148.0 Clamp.

It is a genuine item that is supplied by the original equipment manufacturer for Karcher pressure washers. This is an identical replacement for a faulty or a missing metal fork that was installed on a new unit. To ensure the exact location and the correct replacement procedure, refer to the appropriate diagrams for your model. Note, this ...Read morehigh-quality fork is made of durable metal and is sold as an individual item. A screwdriver, a wrench set, and pliers might be needed to perform this repair.

This is an authentic Karcher part is specially designed for use with pressure washers. It is utilized to provide a tight seal for the housing. Unfortunately, over time the material will wear out and it may begin to crack eventually requiring a replacement. Keep in mind this high-quality part is made of durable rubber and is sold individua...Read morelly. Refer to the appropriate diagrams of your model to ensure the correct replacement procedure. A wrench set and a screwdriver will be needed to perform this repair.