This light bulb is a 40 watt, 130-volt clear appliance light bulb that is manufactured to fit microwaves with small-base light bulb sockets. The light bulb illuminates the inside of the microwave while the microwave is running. You may need to replace this part if the existing one is burnt-out or broken. If the existing light bulb is brok...Read moreen, disconnect power to the microwave and remove the bulb base with a pair of needle nose pliers. This is a common wear item, so it is recommended to order a spare. These light bulbs are sold individually.
This is a replacement grease filter for your microwave. Sometimes known as the air filter, this part fits underneath your microwave and catches grease. As a result, your grease filter can become clogged, and this is the part you will need to replace it. It measures approximately 7 inches by 7 inches. Most microwaves have two grease filters, but this part is sold individually.
This light bulb socket that is used in microwaves. The socket is meant to fit small-base light bulbs. * Please note: The light bulb is not included with this part and is sold separately. If the following symptoms occur, you may need to replace this part: existing socket is broken or cracked, light bulb is not turning on, or new light bulb...Read more does not work. Remember to unplug microwave before installing this part and refer to the manual provided by the manufacturer for installation instructions and a detailed diagram.
The secondary door switch is a simple on/off mechanism that stops the microwave from operating when the door is open (normally opened). The switch monitors the door latch position, and communicates whether the door is open or closed to the electrical control board. This door switch is approximately 1 inch long, and has 2 metal prongs cal...Read moreled terminals that extend out of its body. Common symptoms related to a faulty secondary door switch include: microwave will not turn/shut off, or the microwave will not heat properly.
NOTE: Before you begin this repair, first make sure your microwave is unplugged, and that your capacitor is discharged. A capacitor stores large amounts of electricity even when your microwave is unplugged.
The microwave glass light lens protects the light bulb inside the appliance. It is clear in color and measures approximately 6-1/2 inches long, and 2-1/2 inches wide. You may notice that this part is cracked or broken and will need to be replaced. You will need to remove the screw holding the cover in place. Unhook the cover from the bott...Read moreom panel. Bend the tabs up that are securing the old lens in place. The textured side should be facing up. Place the new lens into place and secure back into place.
This charcoal filter is used to prevent odors and smells from your microwave from being released into your home. If your microwave smells bad or is produce an abnormal or unnatural smell, this filter is likely in need of replacement. Because it is made of charcoal, this filter will eventually need to be replaced, depending on how often yo...Read moreu use your microwave. To replace this filter, some disassembly of your microwave will be necessary. This filter measures 9-inches long by 4-inches wide, and is sold individually.
Unplug your microwave before attempting this repair. You will need to remove the grill, which is held into place by two screws at the top of the grill (open your microwave door before doing this). Remove the grill. Remove the screw on the left holding the control panel in place. Loosen the screw behind the panel. You should now be able to...Read more lift the panel up and pull forward to detach. You will find the door switch by removing the screws to detach the switch assembly. Press on the release tab to remove the middle switch. Disconnect the wire connector to release the old switch. The door switch is normally closed.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Cameron - For model number JVM7195BL1TS
June 21, 2022
The filter light came on the microwave so I went to check the charcoal filter and it is not what is in the owners manual. The filter looks exactly like the LG lmv2031 first filter. Why cant I find this filter under any GE parts list?
Hello Cameron, Thank you for contacting us. We have researched the model you have provided and have found the part you are looking for is PartSelect Number: PS7783258 for the Charcoal Filter and PartSelect Number: PS3506741 for the Grease Filter. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
Looking for cooktop nite/light bulb. Says to replace with 120 volt, 50 watt (max) halogen bulb where can I get the bulb?
Hello Shirley, thank you for reaching out. We have researched and found the Halogen Light Bulb you are looking for, the part number is PS651484. Please reach out to customer service if you need help placing an order, anyone will be happy to assist you. We hope that helps.
Get message steam sensor problem when trying to cook potato
Hi Catherina, thank you for the question. The issue is probably with the steam sensor and you may need to replace it with part number PS237391. We hope this helps, good luck with the repair!
in reheat mood and potato setting it over cooks' things then something about a sensor issue??
Hello AJ, thank you for reaching out. The issue is likely related to a faulty steam sensor. These automatic cooking functions rely on the sensor to detect moisture levels inside the microwave to adjust cooking time. When the sensor malfunctions, it can misread the humidity level, causing the microwave to run longer than necessary. Try cleaning the sensor area inside the cavity to remove any residue that could interfere with readings. If the issue persists, the steam sensor, part number PS237391, may need to be replaced. We hope this solves your problem!
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
light worked, timer and control pad worked, but no turntable, no heat, no noises of any sort, just didn't start up
320 of 387 peoplefound this instruction helpful.
Marla from Arlington, TX
Easy
Less than 15 mins
Screw drivers
Noted on partselect.com that someone else with this problem, found it to be secondary door switch. There are three door switches in this model, but online info noted that one of the three might feel "soft" (in my case, one switch clicked in a rather "jiggly" way, the other two were strong decisive clicks.) To access the door switches on
... Read more this model was the only difficult part. First use a torx bit to remove the two torx screws below the latches inside the microwave. This frees the latching part inside, that holds the door switches, which you will remove after you take off the control panel. The top grill has to come off before you can remove the door panel. Remove the screws above the grill, on the microwave top cover, The grill on this model is covered with a panel that moves out when it vents. After removing the two top screws, the covered grill vent slides left to remove. Be careful, as the sliding tabs are plastic. Wiggle and jiggle it, to slip it off. Below the removed grill, is a small metal grill with one screw in lower center. Remove that screw, and wiggle that out. You'll then see the one screw that holds on the control panel. Remove this screw, and lift the control panel up to remove. Again, go slowly and gently, as the bottom tabs holding the control panel in, are also plastic and easily broken. Lay the control panel on something, (I used the coffee maker) and pull out the wire bundles tucked on the left, that are attached to the latching panel. Wiggle the latching panel gently to lift it up off of it's plastic tabs and pull it out towards you, so you can see the three door switches. Each switch (part number WB24X829) has a little black switch on it. Feel each switch with either your finger, or a screwdriver to see which one doesn't "click" strongly. The weak one is the one you will replace. The door switches are fitted into a tab, and plugged into their wires. Remove the defective switch, pull out the wires, and replace it with the new switch, plugging back the wires, and slipping it back into it's plastic tabs. Then put everything back together in reverse order. The entire job took me fifteen minutes EXCEPT for figuring out how to slide off the upper grill, which I have told you. A repairman would have cost $150, the part was $18. AND, there's a good chance, the other two switches will get "used up" in the next year or so as well, so I'll be ready next time. Thank you, Partselect, why work all day, to make money, only to give it to somebody else, for fifteen minutes of work. All I needed was the knowledge.
Read less
Was this helpful?
Thank you for voting!
Light bulb out, tried to remove, lamp socket broke
222 of 270 peoplefound this instruction helpful.
Gene from Urbana, IL
Really Easy
Less than 15 mins
Screw drivers
Above the stove mounted microwave. I dropped the lens cover from under the bulb and tried to remove the bulb. The bulb separated from the base. I tried to remove the base with a pliers and the lamp socket broke. I ordered the parts and dropped the bottom cover of the unit down (5 screws). Removed 1 screww from the lamp socket, unplugged t
... Read morehe wires and took it out. Simply replaced socket, fastened bottom cover of microwave, installed new bulb and closed lens cover.
bulb had broken off in base that was still screwed into socket
93 of 109 peoplefound this instruction helpful.
william from san antonio, TX
A Bit Difficult
15 - 30 mins
Pliers, Screw drivers
At first I tried to use pliers to unscrew the base,very uncomfortable working position,upside down and backwards(the microwave is installed over the range top)very limited space for your body and arms to manuver and you really cant see the base,all of this took place after the breaker was turned off ofcourse,finally figured out that you c
... Read morean drop the entire bottom housing of the microwave by unscrewing 6 screws and the light sockets are easily accessable once you lower it,take out 1 retaining screw ,remove the entire socket and unscrewed the broken base and replaced the bulbs,I said bulbs,there is no sense in having to replace another bulb in who knows how long since only one had burned out but they were both the same age
My Orders
