Switch to Classic
1 question answered by our experts.
Models
>
JVM1860SF001
JVM1860SF001 General Electric Microwave - Overview
Sections of the JVM1860SF001
[Viewing 2 of 2]Keep searches simple, eg. "belt" or "pump".

Grease Filter
In Stock
PartSelect #: PS227998
Manufacturer #: WB06X10288
This metallic vent hood filter collects grease particles in the air from cooking. This part is sold individually.
$23.59


Drive Motor
In Stock
PartSelect #: PS237772
Manufacturer #: WB26X10038
This is a microwave turntable drive motor. This is a genuine OEM replacement part. It accepts a D-shaped drive shaft. The drive motor is located under the glass microwave turntable, and allows the tur...
$67.01


Halogen Light Bulb
In Stock
PartSelect #: PS651484
Manufacturer #: WB36X10213
This halogen light bulb is an inch and a half long. Carrying 120 volts and 20 watts, it is used with some microwave ovens.
$14.30


Secondary Door Switch
In Stock
PartSelect #: PS237421
Manufacturer #: WB24X829
The secondary door switch is a simple on/off mechanism that stops the microwave from operating when the door is open (normally opened). The switch monitors the door latch position, and communicates w...
$39.70


Glass Light Lens
In Stock
PartSelect #: PS247275
Manufacturer #: WB36X10071
The microwave glass light lens protects the light bulb inside the appliance. It is clear in color and measures approximately 6-1/2 inches long, and 2-1/2 inches wide. You may notice that this part is ...
$14.83


Glass Turntable Coupler
In Stock
PartSelect #: PS227859
Manufacturer #: WB06X10144
This part accepts a D-shaped motor shaft.
$16.48


Glass Cooking Tray
In Stock
PartSelect #: PS250009
Manufacturer #: WB49X10063
This tray rotates in your microwave ensuring more even temperatures and is approx.14-1/2 inches in diameter.
$88.26


Charcoal Filter
In Stock
PartSelect #: PS224009
Manufacturer #: WB02X10733
NOTE: The charcoal filter cannot be cleaned. It must be replaced. This metallic vent hood filter collects grease particles in the air from cooking.
$50.95


Monitor Door Switch
In Stock
PartSelect #: PS237422
Manufacturer #: WB24X830
Unplug your microwave before attempting this repair. You will need to remove the grill, which is held into place by two screws at the top of the grill (open your microwave door before doing this). Rem...
$32.83

Questions And Answers for JVM1860SF001
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Roger
October 6, 2021
Parts for exhaust door
For model number JVM1860SF001

Hello Roger, Thank you for contacting us. We have researched the model you have provided and have found the part you are looking for is PartSelect Number PS651224. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
Was this helpful?
Thank you for voting!
Related Parts:
Common Symptoms of the JVM1860SF001
[Viewing 7 of 7]Won’t turn on
Fixed by
these parts
these parts



Show All
No heat
Fixed by
these parts
these parts



Show All
Tray won’t turn
Fixed by
these parts
these parts



Show All
Doesn’t shut off
Fixed by
these parts
these parts


Show All
Touchpad does not respond
Fixed by
these parts
these parts


Show All
Noisy
Fixed by
these parts
these parts


Show All
Door not closing properly
Fixed by
these parts
these parts


Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Microwave completely stopped working
Turned out the issue was easily solved by replacing a single, inexpensive fuse.
First off, UNPLUG THE MICROWAVE.
The fuse is located under the plastic grill at the top of the microwave. It's held on by two screws. Once you've removed the screws and taken off the plastic grill, you go to the right side of the microwave and remove another screw that holds a small metal grill in place. Removing the small metal grill is probably the toughest part of this repair. You kind of have to rock it back and forth a bit to get it to release. Once that's off, you can get to the fuse. I removed the burnt out one with a pair of needle nose pliers. I also put a small piece of cardboard under the fuse when I did this so I didn't accidentally drop it into the innards of the microwave. I did the same thing when I replaced the new fuse. I then plugged the appliance back in and made sure it worked. Once that was confirmed, I replaced both grills.
First off, UNPLUG THE MICROWAVE.
The fuse is located under the plastic grill at the top of the microwave. It's held on by two screws. Once you've removed the screws and taken off the plastic grill, you go to the right side of the microwave and remove another screw that holds a small metal grill in place. Removing the small metal grill is probably the toughest part of this repair. You kind of have to rock it back and forth a bit to get it to release. Once that's off, you can get to the fuse. I removed the burnt out one with a pair of needle nose pliers. I also put a small piece of cardboard under the fuse when I did this so I didn't accidentally drop it into the innards of the microwave. I did the same thing when I replaced the new fuse. I then plugged the appliance back in and made sure it worked. Once that was confirmed, I replaced both grills.
Parts Used:
-
Kim from Cliffside Park, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
888 of 1135 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dirty filter - replacement filter installed
-
Laura from Sugar Grove, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
534 of 608 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
turntable made a loud noise
First I unscrewed the screws that were holding the panel underneath. Then I removed the panel and removed the screws that held the turntable motor in place. Then replaced the old motor with the new and screwed everything back into place.
Parts Used:
-
Dianne from Westminster, CO
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
372 of 378 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!