Models
>
JVM1640SJ02
JVM1640SJ02 General Electric Microwave - Overview
Sections of the JVM1640SJ02
[Viewing 7 of 7]Manuals & Care Guides for JVM1640SJ02
Click to downloadKeep searches simple, eg. "belt" or "pump".
FUSE
PartSelect #: PS1481237
Manufacturer #: WB27X10928
This ceramic microwave fuse is just over an inch in length. It is white in the center, and metal on both ends. This is a 20-amp fuse, and is used to power your microwave. If the touch pad on the micro...
$10.58
In Stock
Grease Filter
PartSelect #: PS228066
Manufacturer #: WB06X10359
Sold individually. Most microwaves require 2.
$54.19
In Stock
Glass Turntable Tray
PartSelect #: PS1016243
Manufacturer #: WB49X10176
This tray rotates in your microwave ensuring more even temperatures.
$88.85
In Stock
Light Bulb
PartSelect #: PS1481517
Manufacturer #: WB36X10328
Sold individually. Appliance may take 2.
$26.65
In Stock
Exterior Door Frame - Black
PartSelect #: PS1017375
Manufacturer #: WB55X10813
This is not the entire door, just the framing around the front of it.
No Longer Available
EXHAUST ADAPTER
PartSelect #: PS12709817
Manufacturer #: WB02X32715
This is the replacement damper bracket for your microwave. It is made of plastic and is approximately 11 inches wide and 3 inches long. The damper bracket attaches to the outer cabinet and directs air...
$8.54
In Stock
Door Latch
PartSelect #: PS952070
Manufacturer #: WB02X11096
Used to keep the microwave door closed during operation.
$10.42
In Stock
Rotating Ring
PartSelect #: PS1019285
Manufacturer #: WB06X10689
This part sits underneath the glass turntable tray.
No Longer Available
Plastic Rivet
PartSelect #: PS222397
Manufacturer #: WB01X10055
This part is the replacement plastic rivet, or stirrer fan cover clip for your microwave. It is made of white plastic and is approximately ¼ inch in diameter, and ½ inch long. The plastic rivet holds ...
$9.49
In Stock
Charcoal Filter
PartSelect #: PS783520
Manufacturer #: WB02X10943
It is recommended to replace this filter yearly.
$46.31
Special Order
Damper
PartSelect #: PS952387
Manufacturer #: WB06X10565
This vent damper is a manufacturer-approved replacement part for your above-range microwave. This part helps vent air from the microwave to the exterior of your home, and helps keep exterior wind out ...
$15.99
In Stock
Vent Grille - Black
PartSelect #: PS1020368
Manufacturer #: WB07X10967
This vent grille mounts on the top of the microwave above the door.
$99.63
In Stock
Questions And Answers for JVM1640SJ02
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the JVM1640SJ02
[Viewing 5 of 5]No heat
Fixed by
these parts
these parts
Show All
Won’t turn on
Fixed by
these parts
these parts
Show All
Touchpad does not respond
Fixed by
these parts
these parts
Show All
Door not closing properly
Fixed by
these parts
these parts
Show All
Tray won’t turn
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Microwave completely stopped working
Turned out the issue was easily solved by replacing a single, inexpensive fuse.
First off, UNPLUG THE MICROWAVE.
The fuse is located under the plastic grill at the top of the microwave. It's held on by two screws. Once you've removed the screws and taken off the plastic grill, you go to the right side of the mic ... Read more rowave and remove another screw that holds a small metal grill in place. Removing the small metal grill is probably the toughest part of this repair. You kind of have to rock it back and forth a bit to get it to release. Once that's off, you can get to the fuse. I removed the burnt out one with a pair of needle nose pliers. I also put a small piece of cardboard under the fuse when I did this so I didn't accidentally drop it into the innards of the microwave. I did the same thing when I replaced the new fuse. I then plugged the appliance back in and made sure it worked. Once that was confirmed, I replaced both grills.
First off, UNPLUG THE MICROWAVE.
The fuse is located under the plastic grill at the top of the microwave. It's held on by two screws. Once you've removed the screws and taken off the plastic grill, you go to the right side of the mic ... Read more rowave and remove another screw that holds a small metal grill in place. Removing the small metal grill is probably the toughest part of this repair. You kind of have to rock it back and forth a bit to get it to release. Once that's off, you can get to the fuse. I removed the burnt out one with a pair of needle nose pliers. I also put a small piece of cardboard under the fuse when I did this so I didn't accidentally drop it into the innards of the microwave. I did the same thing when I replaced the new fuse. I then plugged the appliance back in and made sure it worked. Once that was confirmed, I replaced both grills.
Read less
Parts Used:
-
Kim from Cliffside Park, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
953 of 1228 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Outer frame had a crack and needed to be replaced
Had to discover how to do this the hard way, but the 1st thing you need is a blow-up diagram of the door which you can download from GE's website.
Note that all the components in the door save for the 2 handle screws are snap-on.
You will need a screwdriver and a putty knife.
The door assembly is on a simp ... Read more le pivot hinge which you can lift and pull off the microwave, making it easier to work.
On the inside face of the door, locate strip where the outer edge meets the inner door. The plastic strip is about 2" wide and goes all the way around the door. Remove this strip using a putty knife working around it to gently pry it off. Push putty knife into space between plastic strip and outer door panel. This will give access to the 2 handle screws.
Unscrew the screws and remove handle.
Using putty knife and starting at the top edge of the door near the center, gently pry the outer frame from the latching tabs until the frame comes off.
Snap on new frame and working backwards, screw back the handle, then snap back the the plastic strip and rehang your door on the pivot hinge.
Remember the parts are plastic so don't over tighten the screws.
Also remember to clean the outer glass panel inside and outside before snapping on the outer frame or your fingerprints will be on your microwave.
Note that all the components in the door save for the 2 handle screws are snap-on.
You will need a screwdriver and a putty knife.
The door assembly is on a simp ... Read more le pivot hinge which you can lift and pull off the microwave, making it easier to work.
On the inside face of the door, locate strip where the outer edge meets the inner door. The plastic strip is about 2" wide and goes all the way around the door. Remove this strip using a putty knife working around it to gently pry it off. Push putty knife into space between plastic strip and outer door panel. This will give access to the 2 handle screws.
Unscrew the screws and remove handle.
Using putty knife and starting at the top edge of the door near the center, gently pry the outer frame from the latching tabs until the frame comes off.
Snap on new frame and working backwards, screw back the handle, then snap back the the plastic strip and rehang your door on the pivot hinge.
Remember the parts are plastic so don't over tighten the screws.
Also remember to clean the outer glass panel inside and outside before snapping on the outer frame or your fingerprints will be on your microwave.
Read less
Parts Used:
-
Luis from Fort Worth, TX
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
33 of 36 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No power to microwave, no heating.
Unpluged power cord!! Removed front control panel to expose electronics (need to remove top horizontal vent cover to expose mounting hardware). Unplugged leads to control panel board. Removed magnetron with Tstat (3- phillip heads, need stubby). Installed new parts and control panel, plugged it in tested. Done.
Parts Used:
-
Michael from Coulterville, CA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
47 of 79 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!