My Orders
JMV9196CB4 Whirlpool Microwave Oven Combo - Overview
Diagrams for JMV9196CB4
See every part. Know exactly what you need.
Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".
Search filter:
Clear Filter
Your search term must have 3 or more characters.
$16.07
In Stock
Charcoal Filter
Part #8206230A
This Charcoal Filter traps grease from your oven's exhaust to help prevent it from entering the vent, which could cause damage over time. If the exhaust fan on your microwave is not working, you may need to replace your charcoal filter. This charcoal filter is located within the intake grille of your microwave, which will need to be unscr...Read moreewed and opened to gain access to the filter. The manufacturer recommends that you change your charcoal filter every six months. This filter measures 5 inches by 5.375 inches by 0.375 inches. Be sure to measure your current filter to assure correct replacement. This product is sold individually. We recommend the use of gloves during installation to protect your hands from messy grease during your repair. You should also unplug your appliance at the electrical outlet or switch it off at the breaker. Using a Phillips screwdriver, unthread the screws securing the grill. Open the door and slide the grill to the left and lift it up to remove it. This will allow access to the filter so it can be either replaced or cleaned. Remember to insert the tabs of the grill into the frame and slide it to the right when you are done. To finish, shut the oven door and secure the grill with the screws.
Read less
$27.36
In Stock
Grease Filter
Part #W10208631A
This Grease Filter is constructed of Acrylonitrile Butadiene Styrene and is used to trap grease and help eliminate odors from the exhaust air while cooking. It attaches onto the exhaust and is rated as easy to install. The part is 12 15/16" x 5 3/4", and comes in silver. Refer to your make and model number to ensure this part is right fo...Read morer you. If the exhaust fan of your appliance is not working, this part is the most likely cause. This part is sold individually, and it should be noted that many microwaves require two filters, so you may need to replace both at the same time by purchasing two of this part. You should consider gloves during this simple repair (which requires no tools) to save yourself from getting greasy hands.
Read less
$18.22
In Stock
Microwave Surface Light Bulb
Part #W10709921
This microwave surface light bulb (120v 25w) is an OEM replacement part used in microwaves and microwave/hood combos. It is one of the two halogen lightbulbs that are positioned on either end of the base of the appliance to illuminate the cooking surface. The light allows you to easily monitor the cooking/heating process. Over time the li...Read moreght bulb may burn out or break resulting in difficulty viewing the cooking surface, and increased chances of injury while cooking. To replace the bulb, unplug the appliance and remove the light cover/lens, to access the bulb housing. Carefully unscrew the old bulb from its socket to avoid breaking it and damaging the assembly. Inspect the socket to check that it is in good working condition. If both of your light bulbs fail at the same time, the socket may be experiencing an electrical fault and will need to be replaced. Install the new bulb by screwing it into the socket. Reattach the light cover and plug in the appliance to check that the light bulb is functional. Each light bulb is sold individually.
Read less
$23.60
In Stock
Mounting Plate
Part #W11025649
This mounting plate is sourced directly from the original manufacturer for use with microwaves. It is a metal plate designed to support a microwave by attaching the microwave to the wall studs. If the mounting plate wears down or becomes damaged, it will cause the microwave to tilt and become unstable, potentially damaging the appliance a...Read morend the wall it is attached to. Therefore, it is important to replace the plate promptly. First disconnect the microwave from the power source and locate the fasteners that hold the mounting plate. Detach the old plate and align the new one with the existing mounting holes. Secure the plate and check that the microwave is stable and unmoving.
Read less
$9.62
In Stock
Door Switch - 3 Terminal
Part #W10727360
This three-terminal switch fits your microwave door. This part is mostly black in color and is about 1.5 inches with metal terminals. You might need to replace this part if your microwave is not heating properly or if it runs for a few seconds but turns off.
$8.55
In Stock
$31.58
In Stock
Microwave Door Interlock Switch
Part #W10269458
This door interlock switch is a genuine replacement part designed for use in microwaves. It serves a critical safety function by preventing the microwave from operating when the door is open. Because proper operation of the microwave’s shielding and interlock system is essential for user safety, this part should be installed by a qualifie...Read mored service technician. After installation, the interlock switches and microwave shielding must be thoroughly tested to ensure the appliance meets safety standards.
Read less
$26.82
In Stock
DIODE
Part #W11256462
This diode, or high voltage diode, is used in microwaves. It is an electrical current control device that ensures power flows in one direction and not the other way. If your microwave produces no heat, heats inconsistently, or gets noisy, replacing this part can be the solution. The tools needed for this replacement are a nutdriver, plier...Read mores, and screwdrivers. First remove the microwave cover, then remove the old part by disconnecting the small thermostat. Replace with the new diode. Remember to use the diagram provided by the manufacturer for more instructions.
Read less
$36.85
In Stock
R Ceramic Fuse 20 A
Part #W11707984
If your microwave is not turning on it could be due to your fuse needing to be replaced. This part protects the microwave by shutting it off if there is an electrical surge. This fuse is just over an inch long, is metallic on both ends and ceramic in the middle. Before beginning this repair, unplug the appliance and wait a few minutes bef...Read moreore starting. Remove the outer cabinet which is held in place with two screws. You will then locate the power cord which will lead you to the fuse holder. Determine if the fuse has blown. Using an ohmmeter, you should be able to figure out if it has blown. A proper reading is zero ohms, if it reads as anything else then your fuse has in fact blown. Simply snap the old fuse out of place and place the new one in.
Read less
$51.65
In Stock
Microwave Glass Turntable Tray
Part #W11402532
The turntable tray rotates in the centre of the microwave to help ensure the food cooks evenly.
$9.62
In Stock
Drive Coupling
Part #W10337248
This glass tray drive coupling, also known as a tray support, is a genuine OEM replacement part. It can help solve the issue of your microwave tray not turning properly. This motor couple connects the motor to the turntable. To replace this part, make sure the microwave is unplugged first. Remove the glass tray, and the existing coupling. Insert the new coupling into the motor shaft.
$60.51
In Stock
Microwave Damper
Part #W10843943
This damper is an authentic OEM replacement assembly used in microwave/range hood combos. It includes the damper door and frame. It is designed to direct the flow of air through the vent duct, and the release of steam and heat from the appliance during cooking. Over time, the damper door and frame can wear down or become obstructed by foo...Read mored particles and debris. A faulty damper assembly will result in poor ventilation, uneven cooking, and excessive moisture buildup which can damage internal components in the appliance. Disconnect any wires or connectors attached to the faulty damper assembly and remove it from the appliance. Position the new damper assembly and reconnect the wires/connectors before securing it with the appropriate fasteners.
Read less
Common Symptoms of the JMV9196CB4
How this model fails, and the parts that fix it.
Won’t turn on
Fixed by
these parts
these parts
Show All
No heat
Fixed by
these parts
these parts
Show All
Door not closing properly
Fixed by
these parts
these parts
Show All
Tray won’t turn
Fixed by
these parts
these parts
Show All
Exhaust fan not working
Fixed by
these parts
these parts
Show All
Noisy
Fixed by
these parts
these parts
Show All
Doesn’t shut off
Fixed by
these parts
these parts
Show All
Touchpad does not respond
Fixed by
these parts
these parts
Show All
Watch our pros, then fix it yourself.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!
View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Door switch inconsistent operation for Open/Close sensing.
142 of 173 people
found this instruction helpful.
Ordered top & bottom micro-switches and mounting plate parts. Internet reviews could not find specifics if the issue was due to a top/bottom or combination of micro-switch or mounting plate failure. Pulled the plug. Removed the top vent assembly cover held in by 2 Phillips screws inside the vent. Removed the control panel held in by 1 P
... Read more
hillip screw at the top vent assembly area. Lifted control panel upward to release the catch and moved it off to the side - didn't disconnect any leads. Used a Torx bit to remove the door switch mounting plates at the front and pulled the plates through the opening from the control panel. Documented the wire color code connections, the top plate uses 2 micro's with one using both the closed & open contact. Installed the respective micros on the mounting plates and worked backwards with the wiring and removal steps. Once completed, the open/close sensing has worked every time.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!