JMP261D1 General Electric Range - Overview

This is a 240 volt bake element for your oven or range. The kit comes with two installation screws and the element. The element functions by supplying heat from the bottom of the oven to bake or cook your food. You may need to replace the bake element if your oven is not heating properly. This is a black metal part (Width 13 inches, lengt...Read moreh 16.5 inches, depth 1-1/2 inches ) which can be installed onto your range with a screwdriver. Installation is rated as "medium" difficulty. This element is the part that heats to allow cooking, and if broken or missing you'll be unable to cook. This part attaches to the lower section of the range. Refer to your model number and user manual to ensure this part is right for you. Each screw gets screwed into each wire terminal with a Phillips screw driver. Hold the wires forward to make sure the wires do not fall back through the rear of the oven. Unplug your appliance or shut off your circuit breaker to the appliance before installing the new part.

This six inch chrome drip bowl is intended for use with tilt lock style surface mount burner element units.

This 6 inch high rise burner trim ring is intended for use with detached style low rise tilt lock surface mount burners on ranges.

This 8 inch high rise burner trim ring is intended for use with detached style low rise tilt lock surface mount burners on ranges.

This eight inch chrome drip bowl is intended for use with with tilt lock style surface mount burner element units.

This 40-Watt light bulb is sold individually. It is specially designed to withstand extreme temperatures, so this bulb is compatible with a variety of appliance types including refrigerators, ranges, microwaves, and dryers. It features a frosted glass bulb with a standard metal socket base, which allows you to easily unscrew the burnt-out light and twist the new bulb into place.

The broil element is located at the top of the oven and gives off heat in order to bake evenly. If you notice that the element is not heating up or is not cooking evenly it could be because it is broken or burnt out. The depth of the screw-on terminals is 2-3/4 inches and they are 1-1/4 inches apart. Does not include mounting bracket. All...Read more you need for this simple repair is small screwdriver. To complete this repair, you will need to first turn the oven off (or shut off the house circuit breaker), remove the two screws that are holding the old element in place, remove the two wires from the old part, and then connect them to the new part and screw back into place.

The infinite switch controls the stove top surface burner. This switch will work with most of the electrical range models with coil burner elements.

This set of 3 clock timer knobs let you set and change the settings on your range clock. These genuine OEM knobs are made of black plastic and measure approximately 1-inch long.

This surface element kit includes an 8 inch element, two wire, 2350 watt surface element, and a terminal block with all three-wire units. These high rise elements do not come with an attached trim ring.

This light bulb lens covers the interior light bulb in an oven, range, or stove. No tools are necessary to replace this part. Simply slide off the wire bracket to remove the existing light bulb lens. Disconnect power to your appliance before this repair. It is recommended to check the light bulb while the lens cover is removed in case it ...Read moreneeds to be replaced. Be sure to remove all broken glass, if applicable, before installing new lens. This part is sourced directly from the genuine manufacturer, and is sold individually.

This 6-inch surface element provides heat for boiling, frying, and simmering on an electric range. Its 3-wire, tilt-lock design runs on 240 volts and produces about 1,325 watts. Replace it if it does not heat, heats unevenly, or has burned or broken areas. Before ordering, inspect the control switch, wire ends, and mounting parts. Confirm...Read more the size, voltage, wattage, and fit with the full appliance model. Turn off the correct breaker and verify that power is off before service. Let the element cool and secure each wire before testing.