The Grate Foot is a black rubber part which attaches underneath the grate in order to protect your stovetop from being scratched, which it does by cushioning the grate on your gas range. If this part appears visibly broken or no longer holds in place, which can happen to these feet over time, then it should be replaced. Check your model n...Read moreumber and user manual to see if this part is right for you. Because this part is sold individually, make sure to order the quantity that you require. We generally recommend checking all of the grate feet on your appliance and replacing them at the same time, since it is an inexpensive part and they tend to wear out at around the same rate. Spares are good to have in the event of future failures. Before beginning this repair, ensure that the surface is cool to the touch. Simply pull the worn or cracked foot out and install the new grate foot. This process should not require any tools or accessories.
This comes set from the manufacturer for Natural Gas. It also includes the conversion to Liquid Propane.
This valve automatically cuts off the flow of gas at a certain pressure.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Paul - For model number JGP970SEK2SS
April 5, 2023
The igniter keeps clicking even when shut off, we spilled liquid on the cook top, unplugged it let it dry and used a blow dryer, but it still clicks
Hi Paul, thank you for reaching out. Based on our research, the issue is most likely with the igniter, part number PS1016133, and you may need to replace it to fix the issue. Before replacing it, we would suggest checking the burner igniter switch to ensure it is not faulty. We hope this sorts out your problem!
Soup boiled over into control switches (there's also oil inside soup). Then sparks/flame were flying out from control switches. I then disconnect the gas top.
After drying and blow drying into control switches with hair dryer, I then reconnect gas top and try to start up one stove but massive sparks flew out from the controller.
What do you think is the problem and what parts do you think need replacing? Please advice! Thank you!
Hi Richard, thank you for reaching out. Based on our understanding of the issue, we would suggest you check the switch and harness assembly, part number PS11721440, and replace it if necessary. We hope this sorts out your problem!
What is the difference between these two parts?
PS1016133
PS 952858
Will both fit JGP970SEK2SS?
PS 952858 looks shorter, will the spring and clip fit onto this one?
Hello Richard, thank you for reaching out. The function of both parts is the same. The igniter and top burner spark electrode both provide the spark that lights the surface burner. We have researched your model and found that the igniter, part number PS1016133, is compatible with your model. We hope this is what you were looking for!
I need to replace the cracked glass top. Is there a repair manual or you tube video available?
Hello Patrick, thank you for reaching out. Make sure that power is disconnected before servicing. Remove all control knobs. Remove all burner caps. Remove the screws securing the burner bases. Use a number 15 torx bit for this removal. Lift the burner bases up from the glass maintop and remove the spark ignition wire from each burner electrode. Lift the cooktop from the burner box bottom. CAUTION: 1. When replacing burner bases on glass top models, do not tighten screws beyond 10 in. lbs. torque. 2. When replacing the burner base on the 18,000 BTU burner, make sure you do not tighten the base too tightly to the burner inlet. Over tightening will cause stripping of the screw. 3. Cooktops: Before removing glass maintop, inspect the installation from below to be sure cooktop is resting on the burner box top mounting flange and not the glass maintop. 4. The rubber seal must be re-installed to prevent spillovers from seeping into the burner box bottom. We hope this helps, good luck with this repair!
Was this helpful?
Thank you for voting!
Corey - For model number JGP970SEK2SS
July 6, 2024
One igniter does not spark. We had some sauce leak into one control knob and it sparked/smoked when we cleaned it. Now it won’t ignite ; however we can manually light the burner so I know gas still flows. I think it is the switch harness. Thoughts?
Hi Corey, thanks for asking us! Based on your symptoms, there are a couple of parts we recommend inspecting: the Spark Module kit, the Burner Wire Harness and the Switch Assembly Harness. If any of these parts show signs of wear or damage, they would need to be replaced. Hope this helps, good luck with this repair.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Grate Foot had worn out
24 of 34 peoplefound this instruction helpful.
Kathryn from Star City, AR
Really Easy
Less than 15 mins
A rubber grate foot on my range top had worn out. I pulled the worn foot out and installed the new grate foot with no tools or accessories. Good as new! Now I don't have to worry about the grate scraping my range top and scratching the paint. I also ordered extras so I won't have to wait if another wears out.
Was this helpful?
Thank you for voting!
After my housecleaner had been here, I noted that 2 of the little rubber feet were missing from the top grates.
4 of 5 peoplefound this instruction helpful.
Anne from Jacksonville, FL
Really Easy
Less than 15 mins
I was pretty upset as the grate wobbled, so I went on line and looked for GE Profile parts. To my amazement, I found the little rubber feet quite easily, and within 2 days they were here at my home. I simply had to stick them in the holes; however, I noted that they did not fit real tight, so I removed them and shot a little glue on the
... Read morem, and they have been in place ever since. Thanks to you guys, I am a happy camper now!!!
Read less
Was this helpful?
Thank you for voting!
burner would not light because spark was skiping to ground elsewhere
3 of 4 peoplefound this instruction helpful.
David A from Spring, TX
Really Easy
Less than 15 mins
Nutdriver
First I removed two screws holding head in place and carefully lifted assembly up using flat screwdriver. I separated old igniter from feed wire with gentle pull. I reversed assembly after cleaning old gasket residue. torque screws back in place after cleaning with small ss wire brsh in dremel tool. Tighten in steps to firm light touch.
... Read more I used new gashket and ignitor.
My Orders
