Models
>
JES1288SH02
JES1288SH02 General Electric Microwave - Overview
Sections of the JES1288SH02
[Viewing 1 of 1]Manuals & Care Guides for JES1288SH02
Click to downloadKeep searches simple, eg. "belt" or "pump".
BUTTON LOCKING
PartSelect #: PS12582530
Manufacturer #: WB03X27704
Locking button for wave guide cover.
No Longer Available
Wave Guide Cover
PartSelect #: PS952413
Manufacturer #: WB06X10591
This part is the replacement wave guide cover for your microwave. It is gray in color and is approximately 3 ½ inches long and 5 inches wide. It has two small tabs at the top that allow it to lock int...
No Longer Available
Light Bulb and Socket
PartSelect #: PS247776
Manufacturer #: WB36X951
This light bulb is sold with the socket. The bulb is 120V and 25W.
$20.99
In Stock
Primary/Secondary Switch
PartSelect #: PS237415
Manufacturer #: WB24X823
This is sold individually. Your appliance would need 2 of these.
$103.49
In Stock
Questions And Answers for JES1288SH02
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Mike
January 6, 2020
When i press the open button it blows the circuit breaker
For model number JES1288SH02
Hello Mike and thank you for writing.
It certainly sounds like it could be a faulty switch PS237415, you should check for signs of damage, and replace if necessary. We hope this helps. Please contact us anytime if you require further assistance.
Was this helpful?
Thank you for voting!
Related Parts:
- < Prev
- 1
- Next >
Common Symptoms of the JES1288SH02
[Viewing 2 of 2]Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Original lamp burned out.
After looking up on the computer a schematic of the unit, all that was needed was removing four screws to remove the top and side cover which was one piece.
Next was removal of electrical connection to burned out lamp, then removing burned out lamp and installing the new lamp and reconnecting electrical connection.
Job was co ... Read more mplete after reinstalling the cover.
Microwave now working with new lamp lighting when in use.
Next was removal of electrical connection to burned out lamp, then removing burned out lamp and installing the new lamp and reconnecting electrical connection.
Job was co ... Read more mplete after reinstalling the cover.
Microwave now working with new lamp lighting when in use.
Read less
Parts Used:
-
Rudy from Huntington, IN
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
73 of 89 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Microwave oven was completely dead.
Continuity checks showed the flame sensor was open. Schematic notes it opens at 217 degrees and closes at 30 degrees. Removed sensor and placed in freezer for twenty minutes. Tested sensor and it was now closed, reinstalled and microwave worked normally. Ordered new sensor in case the original is operating at too low a temperature.
Parts Used:
-
CHARLES from LAKE ARIEL, PA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
29 of 39 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Microwave Was Popping And Shooting Fire Sparks
I removed the plastic plug that held the wavecover in place and pulled the wavecover off. I replaced with new cover and it worked perfect.
Parts Used:
-
JULIE from MACON, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
19 of 19 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!