This filter is made of metal and is intended for use with ranges and cooktops. Grease filters are an important but often neglected part of ranges. If the filter is full, your extractor fan will become noisier, and cause a bad odor to come from your range. Neglecting the grease filter can also pose a fire hazard in your kitchen. Regular ma...Read moreintenance and cleaning of the grease filter is important and will make the part work more efficiently and last longer. It takes about 30 seconds to replace your grease filter. While replacing the filter, take a minute to check for a grease buildup underneath, and clean out any drip-through grease. As per the manufacturer, if this filter is 1/2" less wide than the original, it will still function the same.
This bake element is for the bottom of your oven. The bake element supplies heat for baking. If you find there is little to no heat when baking, a burned out bake element, or food is taking too long to cook, these symptoms could be solved by replacing the bake element. Before starting this replacement, make sure the range is unplugged fro...Read morem the power source or shut off from the house circuit breaker. The tools needed is a Phillips screwdriver. For safety reasons, make sure to wear gloves.
This long oven sensor is also commonly known as a temperature sensor. It is designed for use with ovens and ranges. It is similar to a thermostat; it measures and regulates the internal temperature of your oven cavity. There is an adapter at one end, a probe at the other, and they are connected by an insulated wire. The probe is approxima...Read moretely 7 inches long. You can test the sensor with a multi-meter for functionality. You need to check the model-specific manual to determine what the proper resistance is for your specific appliance. This oven sensor comes with two wire harness adapters and a set of instructions.
This is a surface burner igniter, also known as a top burner ignitor and stove top spark electrode. It is used to generate the spark that lights the surface burner. If your stove will not start, element does not heat, or gas igniter glows but does not light, replacing the igniter can solve these issues. For this installation, you will nee...Read mored a Phillips screwdriver and needle nose pliers. First place the grate on top of the burner, then lift the burner and disconnect the wires. Next remove the two Phillips screws from the bottom of burner, pull igniter out of the burner and wiggle in the new one. Refer to the installation instructions provided by the manufacturer for more instructions.
This is a leveling leg for your oven, range, or stove. The leveling legs on your oven allow your appliance to sit perfectly flat. The new one may be longer in length than your original, but will work the same. Install the new leveling leg, and test if you have it adjusted properly by putting the appliance on four legs. Adjust in or out a...Read mores required if your oven is rocking. It is recommended to check the other three leveling legs on your appliance in case they are also damaged or worn. The leveling leg measures 1.859", is all black in color, and is made entirely out of plastic. This leg may be shorter than the original but is the factory replacement. Longer leg is not available.
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch. It has 6 threads. Refer to the manual provided by the manufacturer for further information on repair and accurate guidance. Remember to wear work gloves as a safety precaution.
This gas valve knob measures approximately 2 12 inches in diameter. It is a black knob that has white lettering aroud its perimeter denoting the different temperature levels: low, medium, high, etc. This valve knob is made of plastic and will accept a 'D' shaped shaft.
The oven door gasket on your range functions as a seal between the warm interior of your oven, and the outside. It prevents heat from fleeing your oven when the door is closed. Before making any repairs to your oven you should make sure to wear work gloves to protect your hands, and give your oven time to cool. The only tool you will need...Read more to make this repair is a pair of needle nose pliers. This oven door gasket comes with built in retaining clips; if any retaining clips from your old gasket are left in the oven make sure to remove them before installing your new gasket.
This part is for oven ranges, it connects individual wires and protects the device from electrical surges, voltages, and current. With this part, the house power is connected to the range wire harness. Some symptoms replacing the terminal block could be a solution for are little to no heat when baking, element will not heat and/or it will...Read more not start. This part will prevent loosening and will reduce damage caused by corrosion (by two different metals). Refer to the instructional diagram for further replacement guidance and exact placement. You must unplug the appliance before installing this part and wear gloves to protect your hands.
This surface burner head is for ranges.
Surface burner head distributes the gas through holes or slots to create an even flame across the cooking area.
Shut off the gas supply and unplug the range before installing this part. Wear work gloves to protect your hands.
This part is a replacement halogen lamp for your oven. The bulb is 25 watts and 120 volts. If your light bulb is burned out, this is the part that replaces it. Be sure to turn off power to your range hood before you begin this repair. This bulb is sold individually and is a genuine OEM part sourced directly from the manufacturer.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
2
3
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Ron - For model number JDS9860AAP
December 13, 2019
I have no spark to the sealed gas burners, gas is flowing but no spark to ignite - what would cause this?
Hello Ron, thank you for writing. You will want to replace the Spark Module, part number PS2094592 for your model range. Good luck with your repair!
4 peoplefound this instruction helpful.
Was this helpful?
Thank you for voting!
JOHN - For model number JDS9860AAP
February 18, 2020
How old is this model? Are spare parts available?If we replaced with a new jennair model, what would come closest to matching the dimensions, look, etc.?
Hello and thank you for writing.
Additional to the model number we also need the serial number to establish the year of your unit. Looking forward to your reply, please always include the model number. We hope this helps. Please contact us anytime if you require further assistance.
Spare parts can be found under :
https://www.partselect.com/AdvancedModelSearch.aspx?ModelNum=JDS9860AAP&mfgModelNum=&fkMfgID=1
The dimensions are under this link :
https://partselectcom.azureedge.net/assets/manuals/D76463F1A4948FF62B42F25DFF9B437469B63B25.pdf
We hope this helps. Please contact us anytime if you require further assistance.
2 peoplefound this instruction helpful.
Was this helpful?
Thank you for voting!
Pat - For model number JDS9860AAP
March 24, 2020
What part is defective to cause f1 code? Thanks,
Hello Pat, thank you for your inquiry. An F1 error code indicates that either the touchpad, or control board has become faulty. Replace touch pad, control board (clock), or both if one assembly. We hope this helps.
2 peoplefound this instruction helpful.
Was this helpful?
Thank you for voting!
Cathy - For model number JDS9860AAP
November 4, 2021
My right back burner only lights with a match ? It won’t work on its own
Hello Cathy, thank you for your question. We have researched the model you have provided, and we would suggest the Top Burner Igniter, part number PS2082000. We hope this helps!
Hi, looking for sealed burner cartridges for this model. Igniter will not work.
Hello Jay, thank you for your question. The Igniter for the two burners is PS2082000. A complete Gas Burner Cartridge with Grates is PS2162200. We hope these options are helpful.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Replace Grease Filter
531 of 547 peoplefound this instruction helpful.
Gene from Washington C.H., OH
Really Easy
Less than 15 mins
Just a couple of minutes to left off the cover grid, left out the old filter and drop in the new one.
Was this helpful?
Thank you for voting!
The element broke in two pieces after food dried on it.
178 of 184 peoplefound this instruction helpful.
Heather from Huntsville, AL
Really Easy
15 - 30 mins
Screw drivers
First, I unplugged the oven. Then, I removed the two screws that hold the element in place. After that, I gently pulled the element toward the front of the oven until the wires were exposed. I disconnected the wires from the old element, removed the old element and then attached the wires to the new baking element. I gently pushed the
... Read more new element back into the screw holes and screwed the new element in place. When I plugged the oven back into the wall I heard a pop and thought I'd blown up the oven! Turns out the breaker popped...after fixing the breaker, I turned the oven on and the element worked just fine. I highly recommend PartSelect.com for their fast shipping and great products. I will be ordering from them again for future appliance parts.
Read less
Was this helpful?
Thank you for voting!
Oven not holding 350 F, when cooling the coils did not reheat
162 of 213 peoplefound this instruction helpful.
David from Westford, MA
Really Easy
15 - 30 mins
Screw drivers
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening,
... Read morereinstall 2 screws. The oven works fine! Note that due to thermal lag the temperature overshoots to 370 degrees and undershoots to 340 degrees, this appears to be normal oven operation. Putting door back in place was easy.
My Orders
.gif "SUPPLEMENTAL INFORMATION Diagram and Parts List for Jenn-Air Range")
