Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
The surface burner or element on your range provides the heat that you cook with. If your element will not heat, you may need to replace the surface burner. This surface burner is 8 inches in diameter...
This large broiler pan is found in the bottom of your oven and is used to catch drippings from broiling foods. This part includes the grate and bottom pan and is made of porcelain. The grate measures ...
Enhance your cooking experience with the GE 6" Surface Element, a genuine, durable top-of-the-line replacement part. This component ensures the heat supply to the cooking area on top of your range, th...
Step 1--cut power to the unit off at the breaker box! Step 2--take a deep breath and dive in. The most difficult part, after getting over the fear, was unscrewing the old unit from the back plate -- been there a LONG time. Step 3, slowly pull the old part forward to see the wires on either side of the old coil. Note how the 'clips' attach
... Read more to the ends. Remove the old unit, being careful not to bend the clips. Slide the new part into the stove. Attach the clips until click securely--be careful not to bend; make sure the clips are secure or you risk losing the wire inside the stove. Once the clips are secure, gently and slowly slide the ends into the holes. The wires and ends will glide into a hole such that the plates on the part align with the back of the stove. Use the old screws and attach the face plate of the part to the back of the stove. The part may rest slightly above the bottom of the stove; this will resolve itself as the part 'adjusts' to the new environment. Turn the breaker back on and turn on the stove. There may be a slight odor the firs time the unit is used; I suggest leaving the door open and heat the coil completely for about 20 minutes. Should be ready to go. (The old unit should be discarded; ask your recycle team if they accept electronic parts or alert the garbage guys that the old part is in the weekly trask.)
No instructions for installation came w/ part. Used some instruction from order web site that someone else had submitted. Once I figured out how the new part connected to the oven's wiring, it was a very easy to install. If you need to ever replace the bake unit all you need to do are basically 5 things: 1. Using a nut driver, remove the
... Read morenut at each of the connection points of the old bake heating element (these are located at the back of the stove). 2. Slowly and gently pull the old element towards you until you see the wires that connect it to the back of the stove emerge from their holes. 3. Gently pull up the ends of the old bake unit which will remove it from the vertical wiring posts--don't let the wired posts slip back into the holes at the back of the oven--I used a little strip of tape to keep them from sliding back into their holes. 4. Gently slip the posts (one at a time) of the new bake unit down and over the vertical wiring posts connectors (press all the way down over the wiring posts) then w/ both hands gently squeeze both of the bake unit ends at the same time and slowly push them back into their holes until the fastening plates press against the back wall of the oven. 5. Align the nut holes, replace nuts and tighten them. I turned the oven on to make sure it worked and let it heat up for a 1/2 hour. Everything worked fine. Don't let this repair intimidate you--just use the right tools, take a deep breath, go slow and be gentle. I'm not in any way mechanically inclined and I did it--so can you.
