Models
>
J63CK1
J63CK1 General Electric Cooktop - Overview
Sections of the J63CK1
[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
Surface Element - 8 Inch - 2350W
PartSelect #: PS243868
Manufacturer #: WB30M2
The surface element, also known as the coil surface element, transfers heat to the area on top of range. The element is 8 inches in diameter. If your surface element does not heat, over heats, or heat...
$61.79
In Stock
Surface Element - 6 Inch - 240V
PartSelect #: PS243867
Manufacturer #: WB30M1
If you notice that your surface element will not heat properly, you may need to replace it. This surface element is 6 inches in diameter and 240V. It is a Y-frame surface burner element with five turn...
$57.41
In Stock
Surface Burner Terminal Block Kit
PartSelect #: PS232606
Manufacturer #: WB17X210
This is a surface burner terminal block kit, also known as range surface element receptacle, for an oven, range, or stove. The kit comes with the terminal block, mounting clip, and wires. This surface...
$78.35
In Stock
Infinite Switch Burner Knob
PartSelect #: PS249164
Manufacturer #: WB3X800
Sold Individually. This knob accepts a double-flat shaft.
No Longer Available
Infinite Control Switch - 8"
PartSelect #: PS236365
Manufacturer #: WB23M1
This is an 8-inch infinite control switch, also known as surface element switch, for a range, oven, or stove. The infinite control switch maintains the heat of your surface burner. Be sure to disconne...
No Longer Available
Surface Burner Switch - 6"
PartSelect #: PS236379
Manufacturer #: WB23M2
This is a surface burner switch. It may also be known as an infinite control switch and it is used in conjunction with your range. The purpose of this part is to control the surface element off and on...
No Longer Available
Maintop Seal - Gray
PartSelect #: PS244598
Manufacturer #: WB32M1
This part is located under the control panel.
$62.77
Special Order
Questions And Answers for J63CK1
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the J63CK1
[Viewing 2 of 2]Element will not heat
Fixed by
these parts
these parts
Show All
Little to no heat when broiling
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
There was no heat on the coils.
I opened the lid, and found that the terminal blocks were burnt, the wires were melted. I ordered one set of terminal block to replace the burnt one, and it worked. Before I started, I shut off the electricity in the whole house to be safe.
Parts Used:
-
Shaohui from East Lansing, MI
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers
48 of 52 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replacement of Coils
Removed by slightly wiggling out of the coupling. No tools needed, seriously, (and I'm a contractor). Basically, pull out and snap back in.
Parts Used:
-
Joseph from South Plainfield, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
35 of 42 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Surface burner coil did not work.
TURN OFF ALL POWER TO KITCHEN. Took off all burner coils and plates below them. Lift hood. Locate part. Remove old part and replace with new part in same way as was previously installed. The wire that comes with the kit is actually too much wire, but just arrange it the best you can and leave it....no big deal. I didn't have a magnet
... Read more
, but needed one. The wire from burner coil to switch runs through a harness which is screwed on to the body of the oven (below the range). Be careful NOT to drop it behind oven when taking it out. I dropped it and took forever to get it. That turned a 20 minuate job into an hour and a half. Otherwise this is an easy job that anyone can do. Refrigerator compressor is next. Have fun.
Read less
Parts Used:
-
Gregory from Mont Belvieu, TX
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers, Socket set
23 of 33 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!