EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

J2S968BEKB General Electric Range - Overview

Diagrams for J2S968BEKB

See every part. Know exactly what you need.

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Grate Foot – Part Number: WB02T10461
$16.09
In Stock
Grate Foot
★★★★★
★★★★★
(21)
Part #WB02T10461
The Grate Foot is a black rubber part which attaches underneath the grate in order to protect your stovetop from being scratched, which it does by cushioning the grate on your gas range. If this part appears visibly broken or no longer holds in place, which can happen to these feet over time, then it should be replaced. Check your model number and user manual to see if this part is right for you. Because this part is sold individually, make sure to order the quantity that you require. We generally recommend checking all of the grate feet on your appliance and replacing them at the same time, since it is an inexpensive part and they tend to wear out at around the same rate. Spares are good to have in the event of future failures. Before beginning this repair, ensure that the surface is cool to the touch. Simply pull the worn or cracked foot out and install the new grate foot. This process should not require any tools or accessories.
REAR SUPPORT – Part Number: WB02X33180
$16.05
In Stock
REAR SUPPORT
★★★★★
★★★★★
(23)
Part #WB02X33180
This genuine GE drawer support is an original replacement part sourced from the manufacturer and is designed for use with electric ranges. Made of durable plastic, it attaches to the rear of the drawer and provides stable support by securing the rear side in place. This part includes the necessary mounting screw for installation and is sold individually. It’s a simple yet essential component for maintaining smooth drawer operation and proper alignment.
Oven Sensor – Part Number: WB23T10015
$40.51
In Stock
Oven Sensor
★★★★★
★★★★★
(20)
Part #WB23T10015
The function of the oven sensor is to detect the temperature within the oven cavity. If you notice that the oven is too hot or too cold, or it is not heating evenly, you may need to replace the oven sensor. The oven sensor is typically located in the back of the oven so you will most likely need to pull your oven out to access it. Many of our customers have rated this repair as easy. You will need a Phillips screwdriver to complete this repair. Be sure to disconnect the power source and shut off the gas valve before doing this repair.
Foot - Leveller – Part Number: WB02X10521
$25.26
On Order
Foot - Leveller
Part #WB02X10521
Sold individually.
Range Screw – Part Number: WB1K5062
$16.05
In Stock
Range Screw
Part #WB1K5062
Screw – Part Number: WH2X930
$16.05
In Stock
Screw
★★★★★
★★★★★
(1)
Part #WH2X930
This screw is sold individually.
Halogen Bulb Kit – Part Number: WB49X29679
$61.40
In Stock
Halogen Bulb Kit
★★★★★
★★★★★
(8)
Part #WB49X29679
This light bulb is used in the interior oven. NOTE: This bulb has looped pins, not the straight pins.
Window Pack Assembly – Part Number: WB56X22160
$311.77
In Stock
Window Pack Assembly
★★★★★
★★★★★
(24)
Part #WB56X22160
This window pack assembly, also known as inner door glass, is supplied directly by the manufacturer for use in range ovens. It has measurements of approximately 22 inches by 14 inches. The inner door glass is situated between the outer door panel and the oven cavity. It acts as a barrier between the heat generated by the oven and the external environment. This provides insulation and protection while allowing users to easily view the oven cavity. It is made of tempered glass and is resistant to high temperatures and thermal shock. If the inner door glass becomes damaged or cracked, heat will escape from the oven, you may be unable to see the contents of the oven and the risk of injury will be increased.
Broiler Pan - Large – Part Number: WB48X10056
$43.18
In Stock
Broiler Pan - Large
★★★★★
★★★★★
(10)
Part #WB48X10056
This large broiler pan is found in the bottom of your oven and is used to catch drippings from broiling foods. This part includes the grate and bottom pan and is made of porcelain. The grate measures 15-1/2 inches wide by 13 inches deep and the pan is about 17 inches wide by 13 inches deep. No tools are required to replace this item, simply pull out the lower drawer of your range, pull down the front of the drawer, slide the pan out and slide the new one into place. This is a genuine part sourced right from the manufacturer.
Front Drawer Support – Part Number: WB48T10013
$16.05
In Stock
Door Gasket – Part Number: WB04T10050
$63.63
In Stock
Door Gasket
★★★★★
★★★★★
(16)
Part #WB04T10050
This oven door gasket is a high-performance seal made from heat-resistant rubber and fiberglass, designed to create an airtight barrier between the oven door and cavity. Measuring approximately 89.76 inches in length, its flexible construction allows for a precise fit across a range of oven models. The gasket plays a critical role in maintaining consistent internal temperatures by preventing heat from escaping, which supports even cooking and improved energy efficiency. Installation is beginner-friendly and typically takes under 30 minutes using pliers. Some versions include up to 25 mounting clips for secure attachment. Signs of wear—such as visible cracks, tears, or heat leakage—indicate the need for replacement to restore optimal oven performance.
Screw – Part Number: WB1M1
$13.92
In Stock
Screw
★★★★★
★★★★★
(1)
Part #WB1M1
Sold Individually.

Common Symptoms of the J2S968BEKB

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven was not coming up to temperature
57 of 77 people found this instruction helpful.
  • Sean from Highlands Ranch, CO
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
I had to remove the oven from the wall because the sensor plug connction is behind the unit. Two screws hold the sensor inside the oven and then I disconnected the lead and pulled the sensor out from the front. I installed the new sensor, tightened the two screws holding it in and connected the lead. Then reinstalled the oven into the wal l. Overall, a very easy repair once you get the oven out.
Was this helpful?
Thank you for voting!
terminal block melted
56 of 77 people found this instruction helpful.
  • jonathan from willow springs, IL
  • Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
The existing terminal block on my Ge oven/Range had melted due to a loose wire causing sparking and starting the plastic casing of the terminal block on fire and melting it, Part select made the part easy to find and had it at my house in 2 days. All I had to do was remove six screws to take the back sheet metal cover off of the oven. U nscrew the terminal connections remove two mounting screws that held the terminal on to the oven body. This was a little trickier than it should have been because the melted plastic had reformed making it very hard to access the mounting screws. i then mounted the new piece and plugged the oven in, it took 15 minutes and was very easy. definitely saved me at-least a $100 for the service call i would have made if finding the part wasn't so convenient
Was this helpful?
Thank you for voting!
Plastic drawer support snapped off
30 of 35 people found this instruction helpful.
  • Jeff Troiano from Sayville, NY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
The repair went very easy. The replacement part was designed differently than the original part. It installed on the rear of the drawer with a screw as the original snapped into the side. This was a bit confusing when researching and looking up the part online.
Was this helpful?
Thank you for voting!