HT25 (2008-01) Jonsered Hedge Trimmer - Overview

This 25-inch fuel line carries fuel from the tank to the carburetor, ensuring proper engine operation. Made from durable clear plastic, it is designed to withstand regular use but may become clogged or brittle over time. Replacing a worn or damaged line can help prevent leaks and restore reliable starting and performance.

This is the Genuine Craftsman replacement part. It is made out of Flexible Rubber and is Sold Individually. The purpose of the 530069216 Tank Purge Line is to return the excess fuel that is in the carburetor after the primer bulb has been pushed. The excess fuel is forced through the purge line back into the fuel tank. Over time the Tank Purge Line will become brittle and crack and will need to be replaced.

The Fuel Line Fitting is a plastic part which attaches two pieces of fuel line together. If broken due to damage/fatigue, there may be a leak and the part must be replaced. Installation is rated as "Easy". Refer to your make, model and diagram to ensure this part is correct for you.

This flywheel is an authentic manufacturer replacement part for use with lawn and outdoor equipment. The flywheel is a heavy, circular disc that has magnets that create an electric charge sent to the spark plug to create the spark that ignites the fuel and air mixture in the engine. It is attached to the engine crankshaft by a key known a...Read mores a shear pin or flywheel key. This assembly is a critical component in the starting and running of your power equipment. Over time, the magnets on the flywheel will wear down, and the flywheel may chip and crack. A faulty flywheel will result in a loss of power, excessive shaking during use, and difficulty starting the equipment. Remove the flywheel using a flywheel puller. Position the new flywheel on the crankshaft and secure it with the retaining nut and flywheel key. This flywheel is sold as an individual replacement part.

The Starter Spring is a metal spring used to restract the rope after you pull it to start the engine. Installation of this OEM part is rated as "Medium" difficulty and requires a screwdriver, nutdriver, and torx bit. The part is installed inside the recoil housing. If broken, the rope will not retract and the part must be replaced.

This metal ring in your engine, known as the piston ring, seals the gap between the piston and cylinder wall. It makes sure that the gases produced during combustion do not escape and that the engine maintains the pressure it needs to run. If the piston ring is damaged, oil can seep into the combustion chamber, causing your engine to exhi...Read morebit rough idling and your machine emit blue smoke. To switch out a defective piston ring, detach the old ring from the piston with a screwdriver. When installing the new ring, you may need to compress it to make it fit properly. Please be aware that this genuine OEM replacement part is bought individually. It is recommended that you replace all the piston rings in your machine at once, as they tend to wear down at the same rate. Carefully review your user manual to determine how many rings your machine needs before placing your order.

The Fuel Cap Asssembly attaches on top off the fuel tank in order to prevent fuel from exiting, or debris from entering. Installation is rated as "Easy" by customers. If broken due to fatigue/wear/damage, you may notice a fuel leak or the smell of fuel, and the part should be replaced. Refer to your make, model and diagram to ensure this is the correct part. This part is plastic, and comes individually sold.

The chainsaw starter rope is a three-foot-long white rope that is approved by the original equipment manufacturer, and which wraps around the recoil pulley and is pulled to start the engine. Installation is rated as "Easy" by customers and requires a screw driver, pliers, and torx screwdriver. If the rope breaks it should be replaced. Ref...Read moreer to your make, model and diagram to ensure this rope is right for your machine.

It is a genuine item that is supplied by the original manufacturer for use with Poulan and Weed Eater chainsaws. This washer-clutch is a special friction disk that helps to engage the clutch by ensuring a right fit between connected components. It provides an identical replacement for a damaged or a missing hardware that was installed on ...Read morea new unit. Check the diagrams of your model for the exact location and the correct installation of this part. One durable metal washer-clutch is included. You may need a screwdriver and a wrench set to perform this repair.

This is an authentic replacement foam filter commonly used on handheld lawn and garden equipment. The purpose of this air filter is to prevent dust and other particles from entering carburetor and engine. Includes one (1) filter per order. Replacing this filter is a quick and easy task. It will only require a phillips head screwdriver. ...Read more • Remove screw that hold filter cover • Remove cover and replace air filter • Reassemble and test your equipment

This is an original Craftsman replacement part. The screw is designed by the manufacturer for use in yard tools such as trimmers, blowers, and brushcutters. This part is made of metal, and is generally used in securing the air box assembly. Please be aware that there are different screws used in the machine. Refer to the parts diagram...Read more to be sure of ordering the correct part. You may require a screwdriver when replacing this item. This part is sold individually.