HS518102 Husky Compressor - Overview

This is an authentic replacement part manufactured for use with Campbell Hausfeld pressure washers. The pressure switch is used to turn the pump on or off depending on the amount of air pressure within the tank. A faulty switch will likely prevent the pump from turning on when the pressure in the tank is low. This switch is available as an individual replacement part, please see model diagram for associative parts.

This part is an OEM from Campbell Hausfeld. The drain cock-npt 3/8 is compatible with many air compressors, and is sold individually. The metal component allows the operator to drain the condensation out from the compressor tank. Located at the base of the tank, a wrench set is required for the replacement. Please be sure to refer the manual for further safety and repair instructions.

Genuine Campbell Hausfeld replacement part, this item is sold individually. The ST033001AV Compression Nut is used to attach the copper tubing to certain components of the compressors listed below. Along with the Compression Nut you will need to use a compression sleeve ( or Ferrule) to seal the tube from leaking air. The Compression Nut will go on the tubing first then the Ferrule will slide into the nut.

It is a genuine OEM part that is made for Campbell Hausfeld air compressors. The unloader valve is an important component which allows a user to safely drain the air from the tank. Unfortunately, over time it may wear out or get damaged eventually requiring a replacement to ensure your unit operates properly. Note, this high-quality unloa...Read moreder includes multiple parts however it is sold as an individual component. Check the owner\\\'s manual and the diagrams of your model to ensure the correct installation and application. You will need a wrench set and pliers to perform this repair.

This is an authentic Campbell Hausfeld replacement part that has been sourced from the original manufacturer to be used with air compressors. The belt attaches to the motor pulley and the pump\\\'s flywheel. This item allows the rotation of the motor\\\'s driveshaft to rotate the pumps crankshaft. This item is sold as an individual replacement part.

This is an authentic OEM part. The 1/2 compression sleeve is compatible with many air compressor machines. With the compression nut, this item helps to secure the exhaust tube to the front shroud. An adjustable wrench is necessary for the replacement. The compression sleeve is sold individually.

1/4

This air filter element is supplied directly from the original equipment manufacturer. Made for use with many air compressors, this item is fitted onto the air filter housing next to the cylinder head. The plastic framed, pleated filter material captures debris from the air as it goes into the compressor. The air filter element is sold individually. Pliers are helpful with making the replacement.

This genuine OEM replacement nipple is designed for use in air compressors, serving as a critical connector between the pressure switch, the tank, and the regulator. A damaged or corroded nipple can lead to air leaks and inconsistent pressure, affecting overall performance. To check for leaks, apply soapy water to the fittings around the ...Read morepressure switch and watch for bubbles. If replacement is necessary, the process typically involves disassembling the pressure switch. Begin by draining the tank using the valve at the bottom, then remove the coupler from the regulator and unthread the nipple. Access the wire connections by removing the pressure switch shroud, and carefully note the position of each wire before disconnecting them—starting with the motor wire, followed by the cord wires and ground wires. Remove the strain relief, pressure gauge, and the airline connecting the check valve to the switch. Finally, unthread the pressure switch from the tank nipple and remove the nipple itself. When reassembling, it is recommended to use thread tape to ensure a proper seal. This replacement part is sold individually.

It is an authentic replacement item that is specially supplied by original equipment manufacturer for use with Campbell Hausfeld air compressors. This is the push-in fitting for the check valve which is sold separately. It is a quick-connect style fitting that is designed to accommodate for 1/4

It is a genuine item that is supplied directly from the original equipment manufacturer for use with Campbell Hausfeld air compressors. A check valve is an important safety feature that will release excess pressure from the tank. If the valve is damaged or missing it should be replaced to ensure your equipment functions safe and properly....Read more One durable metal check valve assembly is included. Refer to the owner\\\'s manual and the diagrams for your model for the correct installation of the new part. You will need a wrench to secure and remove this check valve. Make sure to drain the air from the tank before starting the repair.