HR2811FX Makita Hammer - Overview

Length 8 Foot Length: 6' Gauge: 18 Wires: 2 Type: Bare Wire This power supply cord is a genuine OEM sourced replacement part. It is specially made to supply power from a standard outlet to Makita power tools. A cracked or damaged cord should be replaced before continuing to use the tool. This rubber insulated cord is sold individ...Read moreually. It comes with a rubber sleeve grommet that is not sold separately. Replacing this power supply cord you will need a screwdriver. • Remove the housing screws • Remove the the housing • Disconnect the old cord wires • Remove the old power cord • Secure the new cord in place • Connect the wires • Reassemble and test the new cord

This tapping screw is an authentic hardware that is supplied by original tool manufacturer for use with a variety of Makita power tools. It has multiple uses depending on the model of your unit, please make sure to check appropriate diagrams for correct location and use of this screw. Note this durable metal screw is sold individually.

It is an authentic Makita item that is designed for use with rotary hammers. A guide washer is a special part which helps to provide a tight fit between connected components. This part provides an identical replacement for a damaged or a missing hardware that was installed on a new unit. It is a standard hardware which may have multiple a...Read morepplications. Make sure to check the appropriate diagrams for your specific model for the exact location and the correct application of this guide washer. Note, it is made of durable metal and is sold individually.

This authentic item is supplied directly from the original equipment manufacturer for use with jig saws and rotary hammers made by Makita. The metal bolt attaches to the clamp, the base, and the holder. During replacement, it will require an allen wrench to help install this part correctly. It will need to be replaced if it becomes stripped or broken. This part is available as an individual replacement.

Genuine Makita replacement part. Set of 2 Carbon Brushes with wire lead attached. • Worn brushes are often the cause of a poorly running motor • Replacing brushes can fix an intermittent motor • New brushes can restore a motor's electric braking Carbon motor brushes are one of the most commonly replaced power tool components....Read more Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power. A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned. When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.

This is a genuine OEM sourced replacement o-ring which is utilized on Makita power tools. This component provides an air-tight seal between connected parts, over time the material may become brittle and crack eventually requiring a replacement to ensure the proper seal. It is a high-quality component which is made of durable rubber and it is sold individually.

This is an authentic Makita replacement part that has been sourced from the original manufacturer to be used with rotary hammers. The armature is one of the two main components of the electric motor. The armature is the moving part of the motor and is used to drive the gears. This item is available as an individual replacement part.

This O-ring seal helps maintain proper internal pressure within rotary and demolition hammer mechanisms, supporting efficient operation and preventing leaks of air, oil, or grease. Made from durable elastomer material and measuring approximately 0.63 × 0.63 × 0.63 inches, it is designed to withstand heat and high-pressure conditions durin...Read moreg heavy use. Replacing a worn or damaged O-ring helps restore compression, improve hammering performance, and ensure smooth, reliable tool operation.

This replacement o-ring is supplied directly from the original equipment manufacturer, it is specially designed for use with Makita power tools. It helps to provide an air-tight seal between connected pieces, please make sure to check appropriate diagrams of your model for the correct location and application of this hardware. It is made ...Read moreof high-quality rubber and is sold individually, over time the material may wear out and begin to crack eventually requiring a replacement.

This is a genuine Makita replacement part that has been sourced from the original manufacturer to be used with angle grinders and die grinders. The o-ring is commonly used to seat and support the drive gear bearing assembly. This item is sold as an individual replacement part.

This Ball Bearing is sealed on both sides. This is a genuine Makita replacement part that is sold individually. • Ball bearings are used to reduce friction between rotating parts. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. This reduces wear...Read more on the tool and allows it to run smoothly. • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.